JVC RX-D411S Turning the frequency optimizing function off, Unplug the earphone-type microphones

Page 22

6Unplug the earphone-type microphones.

•When unplugging the microphones, pull on the plug, not the cord itself.

NOTES

•Do not press any buttons on the remote control or the front panel of the receiver during Precise Surround Setup; otherwise, the receiver stops setting and returns to the normal operation mode.

–After “COMPLETE” is displayed, the Precise Surround Setup results are applied to the speaker settings.

•The speaker size measured by Precise Surround Setup may be different from that of the manual setting recommendation (see page 30). Precise Surround Setup measures the speaker size not only by the cone speaker size but also by the other speaker features.

•There may be a case that the receiver fails to detect subwoofer and does not activate it (no optimized test tone comes out of the subwoofer).

In such a case, set the volume level of the subwoofer higher and perform Precise Surround Setup again.

•When you change your listening environment, such as speakers, speaker position, your listening position or so, perform Precise Surround Setup again to optimize the speaker settings.

•Depending on the listening environment, Precise Surround Setup may not measure the speaker settings accurately. In such a case, adjust the settings manually. See pages 29 to 32.

•The supplied earphone-type microphones cannot be used as headphones.

7 Turning the frequency optimizing function off

After performing Precise Surround Setup, the receiver optimizes the frequency response for each speaker. You can turn the frequency optimizing function off.

Press PSS to turn the frequency optimizing function off.

7 Checking the frequency responses corrected by Precise Surround Setup

You can check the current settings of the frequency responses with test tones from speakers and the indications on the display when the frequency optimizing function is activated.

From the remote control ONLY:

1Press TEST to check the frequency response of each speaker on the display.

TEST

•A test tone also comes from each speaker in the following order:

FL (Left front speaker) = C (Center speaker) = FR (Right front speaker) = SR (Right surround speaker) = SBR (Right surround back speaker)* = SBL (Left surround back speaker)* = SL (Left surround speaker) = SW (Subwoofer) * When using a single speaker for the surround back

speaker, the test tone comes out of “SB (Surround back speaker)” instead of “SBR” and “SBL.”

•The frequency response of each speaker appears on the display as follows:

EX. 1: When a test tone comes from the left front speaker

• Each time you press the button, the frequency optimizing

Current speaker

Frequency response

function alternates between on and off.

 

 

 

 

 

 

 

+9 dB

 

 

 

 

 

 

 

When the function is activated, the PSS indicator is lit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optimizing level

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–9 dB

 

 

 

 

 

 

 

 

This function is not available:

 

Low

Frequency

 

 

 

 

High

– Until Precise Surround Setup has been completed at least once;

 

 

 

 

 

 

 

 

 

otherwise, “NO PSS” appears on the display.

EX. 2: When a test tone comes from the subwoofer

– When selecting “A MULTI” for the audio input setting (see page 12).

 

 

 

 

 

 

 

 

 

– When multi-channel PCM signals (see page 41) are coming in with

 

 

 

 

 

 

 

 

Crossover

selecting “HDMI” for the audio input setting (see page 12).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

frequency

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

80 Hz

200 Hz

2 Press TEST again to stop the test tone.

NOTE

While the PSS indicator is off, pressing TEST generates test tones without showing frequency responses. See page 36.

18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents RX-D411S Important for the U.K Information for Users on Disposal of Old Equipment Above ALL Features PrecautionsTable of Contents When operating a DVD player, set the mode selector i to DVD Remote controlParts identification DVR/DVD, VCR, VIDEO, TV, USB, FM, AM Display windowFront Panel TA, NEWS, InfoVideo IN, DVR/DVD Rear PanelVideovcr IN, DVR/DVD IN, Monitor OUT CENTER, SUBWOOFER, SURR-L, SURR-RPutting the batteries in the remote control Before installationGetting started AM MW antenna connection Connecting the FM and AM MW antennasFM antenna connection Close the terminal Connecting the speakersConnecting the speakers Turn the knob clockwiseHdmi connection Connecting video componentsConverting video signals into Hdmi signals Turn off all components before making connectionsFor an analog decoder Scart Terminal SpecificationsScart connection For T-V LinkTo component video output Audio/video connectionComponent S-video Composite To left/right audio channel outputWith analog method When you enjoy the sound recorded in DVD-AudioWith digital method DBS tuner, etc White Red Connecting a VCR and another video componentConnecting a TV Composite video cable not supplied Video cable not suppliedDigital output terminal Connecting the power cordDigital audio connection Digital input terminalsUSB connection How to install the USB driversCheck if the drivers are correctly installed Turn on your PCOperating procedure Before starting Precise Surround SetupVolume of test tones is not adjustable Put on the microphones PSS indicatorIf Precise Surround Setup is not completed properly = SW SubwooferUnplug the earphone-type microphones From the remote control onlyTurning the frequency optimizing function off Press Test again to stop the test toneTroubleshooting for Precise Surround Setup Possible cause SolutionBasic operations 1Turn on the power3Adjust the volume 2Select the source to playSelecting the video input setting Selecting the video and audio input settingsListening with headphones Selecting the audio input settingChanging the display brightness From the remote control only Press Dimmer repeatedlyTo restore the sound, press Muting again Linear PCMFrom the remote control only Press Sleep repeatedly Turning off the power with the Sleep TimerBasic adjustment of auto memory Making sounds naturalTo store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsSelecting the FM reception mode To tune in a preset stationOn the display Press Display while listening to an FM stationPress PTY Search while listening to an FM station About characters shown on the displayPTY codes Description of the PTY codesTest Switching to broadcast program of your choice temporarily News NewsBasic settings Basic setting itemsSubwoofer Operating procedureSetting the speakers Back OUTAuto Activating the EX/ES/PLIIx setting- EX/ES/PLIIxSetting the speaker distance OFFMain Setting bass soundSetting the crossover frequency-CROSSOVER SW LFESetting the Audio delay level Using the Midnight modeLFE ATT Hdmi VCR Setting the auto function modeHdmi Video ManualPress Adjust Sound adjustmentsBasic adjustment items Turn Multi JOG to adjust the selected itemFrom the remote control Adjusting the speaker output levelsAdjust the speaker output levels You can adjust the speaker output levelsATT on Adjusting the sound parameters for the Surround/DSP modesEffect ATT NormalCenter Width DimensionCenter Align Dolby Digital Introducing the Surround modesDolby Surround DTS Extended Surround DTS-ES DTSDTS Digital Surround DTS 96/24Digital Acoustic Processor DAP modes About other digital signalsIntroducing the DSP modes Mono Film3D Headphone mode Using the Surround/DSP modesDTS Virtual Surround Back About the DSP modesAuto Surround DTS-ESTo cancel Surround/DSP modes From the remote control Select and play any sourceTurn Multi JOG to select the Surround DSP mode you want Press SurroundVCR Operating other JVC productsChannel + Release DVR/DVD DVD recorder or DVD playerSET Manufacturer codes for TV Codes JVCManufacturer codes for VCR Codes VCRIf more than one code is listed for your brand of VCR, try CGMTry to operate your DVD player by Pressing DVR/DVD MenuProblem Possible Cause Solution TroubleshootingPower Set the mode selector to the proper Remote control TunerButton before operation Specifications HdmiRX-D411S AUDIO/VIDEO Control Receiver

RX-D411S specifications

The JVC RX-D411S is a versatile and robust audio receiver designed to meet the needs of modern music enthusiasts and home theater aficionados alike. This model stands out with its combination of superior sound quality, user-friendly features, and an array of connectivity options.

At the heart of the RX-D411S lies its advanced amplification system that delivers a power output of 100 watts per channel, ensuring that your audio experience is both dynamic and satisfying. This power rating enables the receiver to drive a wide variety of speakers, making it suitable for various home setups, whether for music listening or movie watching.

One of the most notable features of the RX-D411S is its support for multiple audio formats, including Dolby Digital and DTS surround sound. This allows users to enjoy their favorite movies and TV shows with immersive soundscapes that enhance the viewing experience. Additionally, the receiver is equipped with an FM/AM tuner, providing access to an extensive range of radio stations.

The RX-D411S also incorporates advanced digital signal processing (DSP) technology, which optimizes audio output for various environments, ensuring rich and clear sound reproduction regardless of the space. For music lovers, the receiver supports several audio sources, including CD players, vinyl turntables, and streaming devices, connecting seamlessly through multiple inputs like optical, coaxial, and RCA.

In terms of connectivity, the RX-D411S comes equipped with Bluetooth technology, allowing users to stream music wirelessly from their smartphones and other Bluetooth-enabled devices. This feature adds a layer of convenience to the user experience, enabling effortless access to music libraries and streaming services.

The receiver is designed with a sleek and modern aesthetic, making it a stylish addition to any home entertainment center. Its intuitive interface, supported by a clear and concise remote control, enhances user experience, allowing for easy navigation and adjustments.

Overall, the JVC RX-D411S is an impressive audio receiver that combines power, versatility, and cutting-edge technology. With its broad feature set and reliable performance, it remains a popular choice among audio enthusiasts seeking to enhance both their music and home theater experiences.
Top Page Image Contents