Page 52
To change the transmittable signals for operating a VCR
1 Press and hold VCR .
• Keep the button pressed until step 3 is finished.
2 Press VCR.
3 Enter the manufacturer code using the numeric buttons (1 – 9, 0).
See “Manufacturer codes for VCR” on the right.
4 Release VCR .
Now, you can perform the following operation on the VCR:
VCR
: Turn on or off the VCR.
After pressing VCR, you can perform the following operations on the VCR:
CHANNEL +/–: | Change the TV channel numbers on |
| the VCR. |
| |
1 – 10, 0, h10: | Select the TV channel numbers on |
| the VCR. |
| |
3: | Start playback. |
| |
7: | Stop playback. |
| |
8: | Pause playback. To release it, press 3. |
| |
¡: | Fast-forward a tape. |
| |
1: | Rewind a tape. |
See the manual supplied with the VCR for details.
5Try to operate your VCR by pressing VCR
.
Your VCR turns on or off when you have entered the correct code.
If more than one code is listed for your brand of VCR, try
each one until the correct one is entered.
Manufacturer codes for VCR:
Manufacturer | Codes |
| |
JVC | 01 |
| |
Akai | 02, 36 |
| |
Bell+Howell | 03, 16 |
| |
Blaupunkt | 04 |
| |
CGM | 03, 05, 16 |
| |
Daewoo | 34 |
| |
DIGITAL | 05 |
| |
Fisher | 03, 16 |
| |
G.E. | 06 |
| |
Grundig | 07 |
| |
Hitachi | 08, 09 |
| |
Loewe | 05, 10, 11 |
| |
Magnavox | 04, 05 |
| |
Mitsubishi | 12, 13, 14, 15 |
| |
Nokia | 16 |
| |
Nordmende | 17, 18, 19, 31 |
| |
Orion | 20 |
| |
Panasonic | 21 |
| |
Philips | 05, 22 |
| |
Phonola | 05 |
| |
Saba | 17, 18, 19, 23, 31 |
| |
Samsung | 24, 25 |
| |
Sanyo | 03, 16 |
| |
Sharp | 26, 27 |
| |
Siemens | 07 |
| |
Sony | 28, 29, 30, 35 |
| |
Telefunken | 17, 18, 19, 31, 32 |
| |
Toshiba | 33 |
| |
Initial setting: 01
Manufacturer codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.
Contents
RX-D411S
Important for the U.K
Information for Users on Disposal of Old Equipment
Above ALL
Features
Precautions
Table of Contents
When operating a DVD player, set the mode selector i to DVD
Remote control
Parts identification
Display window
Front Panel
DVR/DVD, VCR, VIDEO, TV, USB, FM, AM
TA, NEWS, Info
Rear Panel
Videovcr IN, DVR/DVD IN, Monitor OUT
Video IN, DVR/DVD
CENTER, SUBWOOFER, SURR-L, SURR-R
Putting the batteries in the remote control
Before installation
Getting started
AM MW antenna connection
Connecting the FM and AM MW antennas
FM antenna connection
Connecting the speakers
Connecting the speakers
Close the terminal
Turn the knob clockwise
Connecting video components
Converting video signals into Hdmi signals
Hdmi connection
Turn off all components before making connections
Scart Terminal Specifications
Scart connection
For an analog decoder
For T-V Link
Audio/video connection
Component S-video Composite
To component video output
To left/right audio channel output
With analog method
When you enjoy the sound recorded in DVD-Audio
With digital method
Connecting a VCR and another video component
Connecting a TV
DBS tuner, etc White Red
Composite video cable not supplied Video cable not supplied
Connecting the power cord
Digital audio connection
Digital output terminal
Digital input terminals
How to install the USB drivers
Check if the drivers are correctly installed
USB connection
Turn on your PC
Operating procedure
Before starting Precise Surround Setup
Volume of test tones is not adjustable
PSS indicator
If Precise Surround Setup is not completed properly
Put on the microphones
= SW Subwoofer
From the remote control only
Turning the frequency optimizing function off
Unplug the earphone-type microphones
Press Test again to stop the test tone
Troubleshooting for Precise Surround Setup
Possible cause Solution
1Turn on the power
3Adjust the volume
Basic operations
2Select the source to play
Selecting the video and audio input settings
Listening with headphones
Selecting the video input setting
Selecting the audio input setting
From the remote control only Press Dimmer repeatedly
To restore the sound, press Muting again
Changing the display brightness
Linear PCM
Turning off the power with the Sleep Timer
Basic adjustment of auto memory
From the remote control only Press Sleep repeatedly
Making sounds natural
Tuning in to stations manually
Using preset tuning
To store the preset stations
Tuner operations
Selecting the FM reception mode
To tune in a preset station
Press Display while listening to an FM station
Press PTY Search while listening to an FM station
On the display
About characters shown on the display
PTY codes
Description of the PTY codes
Test
Switching to broadcast program of your choice temporarily
News News
Basic settings
Basic setting items
Operating procedure
Setting the speakers
Subwoofer
Back OUT
Activating the EX/ES/PLIIx setting- EX/ES/PLIIx
Setting the speaker distance
Auto
OFF
Setting bass sound
Setting the crossover frequency-CROSSOVER
Main
SW LFE
Setting the Audio delay level
Using the Midnight mode
LFE ATT
Setting the auto function mode
Hdmi Video
Hdmi VCR
Manual
Sound adjustments
Basic adjustment items
Press Adjust
Turn Multi JOG to adjust the selected item
Adjusting the speaker output levels
Adjust the speaker output levels
From the remote control
You can adjust the speaker output levels
Adjusting the sound parameters for the Surround/DSP modes
Effect
ATT on
ATT Normal
Center Width
Dimension
Center Align
Dolby Digital
Introducing the Surround modes
Dolby Surround
DTS
DTS Digital Surround
DTS Extended Surround DTS-ES
DTS 96/24
About other digital signals
Introducing the DSP modes
Digital Acoustic Processor DAP modes
Mono Film
3D Headphone mode
Using the Surround/DSP modes
DTS
About the DSP modes
Auto Surround
Virtual Surround Back
DTS-ES
From the remote control Select and play any source
Turn Multi JOG to select the Surround DSP mode you want
To cancel Surround/DSP modes
Press Surround
VCR
Operating other JVC products
Channel +
Release DVR/DVD
DVD recorder or DVD player
SET
Manufacturer codes for TV Codes
JVC
VCR
If more than one code is listed for your brand of VCR, try
Manufacturer codes for VCR Codes
CGM
Try to operate your DVD player by Pressing DVR/DVD
Menu
Problem Possible Cause Solution
Troubleshooting
Power
Set the mode selector to the proper
Remote control Tuner
Button before operation
Specifications
Hdmi
RX-D411S AUDIO/VIDEO Control Receiver