JVC RX-D411S Getting started, Before installation, Putting the batteries in the remote control

Page 10

Getting started

Before installation

7 General precautions

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

7Locations

•Install the receiver in a location that is level and protected from moisture and dust.

•The temperature around the receiver must be between –5°C and 35°C.

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

•Leave sufficient distance between the receiver and the TV.

7 Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

•When you are away on travel or otherwise for an extended period or time, remove the plug from the wall outlet. A small amount of power is always consumed while the power cord is connected to the wall outlet.

The receiver has a built-in cooling fan which operates while the receiver is turned on. Be sure to leave enough ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power cord until all other connections have been made.

Checking the supplied accessories

Check to be sure you have all of the following supplied accessories. If anything is missing, contact your dealer immediately.

•Remote control (× 1)

•Batteries (× 2)

•AM (MW) loop antenna (× 1)

•FM antenna (× 1)

•Dedicated earphone-type microphones (× 1)

•Core filter (× 1)

Putting the batteries in the remote control

1

2

3

Before using the remote control, put two supplied batteries first.

1Press and slide the battery cover on the back of the remote control.

2Insert the batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

•Supplied butteries are for initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity: (+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly at the remote sensor on the front panel.

Remote sensor

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents RX-D411S Important for the U.K Information for Users on Disposal of Old Equipment Above ALL Features PrecautionsTable of Contents When operating a DVD player, set the mode selector i to DVD Remote controlParts identification DVR/DVD, VCR, VIDEO, TV, USB, FM, AM Display windowFront Panel TA, NEWS, InfoVideo IN, DVR/DVD Rear PanelVideovcr IN, DVR/DVD IN, Monitor OUT CENTER, SUBWOOFER, SURR-L, SURR-RPutting the batteries in the remote control Before installationGetting started AM MW antenna connection Connecting the FM and AM MW antennasFM antenna connection Close the terminal Connecting the speakersConnecting the speakers Turn the knob clockwiseHdmi connection Connecting video componentsConverting video signals into Hdmi signals Turn off all components before making connectionsFor an analog decoder Scart Terminal SpecificationsScart connection For T-V LinkTo component video output Audio/video connectionComponent S-video Composite To left/right audio channel outputWith analog method When you enjoy the sound recorded in DVD-AudioWith digital method DBS tuner, etc White Red Connecting a VCR and another video componentConnecting a TV Composite video cable not supplied Video cable not suppliedDigital output terminal Connecting the power cordDigital audio connection Digital input terminalsUSB connection How to install the USB driversCheck if the drivers are correctly installed Turn on your PCOperating procedure Before starting Precise Surround SetupVolume of test tones is not adjustable Put on the microphones PSS indicatorIf Precise Surround Setup is not completed properly = SW SubwooferUnplug the earphone-type microphones From the remote control onlyTurning the frequency optimizing function off Press Test again to stop the test toneTroubleshooting for Precise Surround Setup Possible cause SolutionBasic operations 1Turn on the power3Adjust the volume 2Select the source to playSelecting the video input setting Selecting the video and audio input settingsListening with headphones Selecting the audio input settingChanging the display brightness From the remote control only Press Dimmer repeatedlyTo restore the sound, press Muting again Linear PCMFrom the remote control only Press Sleep repeatedly Turning off the power with the Sleep TimerBasic adjustment of auto memory Making sounds naturalTo store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsSelecting the FM reception mode To tune in a preset stationOn the display Press Display while listening to an FM stationPress PTY Search while listening to an FM station About characters shown on the displayPTY codes Description of the PTY codesTest Switching to broadcast program of your choice temporarily News NewsBasic settings Basic setting itemsSubwoofer Operating procedureSetting the speakers Back OUTAuto Activating the EX/ES/PLIIx setting- EX/ES/PLIIxSetting the speaker distance OFFMain Setting bass soundSetting the crossover frequency-CROSSOVER SW LFESetting the Audio delay level Using the Midnight modeLFE ATT Hdmi VCR Setting the auto function modeHdmi Video ManualPress Adjust Sound adjustmentsBasic adjustment items Turn Multi JOG to adjust the selected itemFrom the remote control Adjusting the speaker output levelsAdjust the speaker output levels You can adjust the speaker output levelsATT on Adjusting the sound parameters for the Surround/DSP modesEffect ATT NormalCenter Width DimensionCenter Align Dolby Digital Introducing the Surround modesDolby Surround DTS Extended Surround DTS-ES DTSDTS Digital Surround DTS 96/24Digital Acoustic Processor DAP modes About other digital signalsIntroducing the DSP modes Mono Film3D Headphone mode Using the Surround/DSP modesDTS Virtual Surround Back About the DSP modesAuto Surround DTS-ESTo cancel Surround/DSP modes From the remote control Select and play any sourceTurn Multi JOG to select the Surround DSP mode you want Press SurroundVCR Operating other JVC productsChannel + Release DVR/DVD DVD recorder or DVD playerSET Manufacturer codes for TV Codes JVCManufacturer codes for VCR Codes VCRIf more than one code is listed for your brand of VCR, try CGMTry to operate your DVD player by Pressing DVR/DVD MenuProblem Possible Cause Solution TroubleshootingPower Set the mode selector to the proper Remote control TunerButton before operation Specifications HdmiRX-D411S AUDIO/VIDEO Control Receiver

RX-D411S specifications

The JVC RX-D411S is a versatile and robust audio receiver designed to meet the needs of modern music enthusiasts and home theater aficionados alike. This model stands out with its combination of superior sound quality, user-friendly features, and an array of connectivity options.

At the heart of the RX-D411S lies its advanced amplification system that delivers a power output of 100 watts per channel, ensuring that your audio experience is both dynamic and satisfying. This power rating enables the receiver to drive a wide variety of speakers, making it suitable for various home setups, whether for music listening or movie watching.

One of the most notable features of the RX-D411S is its support for multiple audio formats, including Dolby Digital and DTS surround sound. This allows users to enjoy their favorite movies and TV shows with immersive soundscapes that enhance the viewing experience. Additionally, the receiver is equipped with an FM/AM tuner, providing access to an extensive range of radio stations.

The RX-D411S also incorporates advanced digital signal processing (DSP) technology, which optimizes audio output for various environments, ensuring rich and clear sound reproduction regardless of the space. For music lovers, the receiver supports several audio sources, including CD players, vinyl turntables, and streaming devices, connecting seamlessly through multiple inputs like optical, coaxial, and RCA.

In terms of connectivity, the RX-D411S comes equipped with Bluetooth technology, allowing users to stream music wirelessly from their smartphones and other Bluetooth-enabled devices. This feature adds a layer of convenience to the user experience, enabling effortless access to music libraries and streaming services.

The receiver is designed with a sleek and modern aesthetic, making it a stylish addition to any home entertainment center. Its intuitive interface, supported by a clear and concise remote control, enhances user experience, allowing for easy navigation and adjustments.

Overall, the JVC RX-D411S is an impressive audio receiver that combines power, versatility, and cutting-edge technology. With its broad feature set and reliable performance, it remains a popular choice among audio enthusiasts seeking to enhance both their music and home theater experiences.
Top Page Image Contents