Weider 831.153931 user manual Cable in the groove of the Pulley, Bolt 100 and a 3/8 Nylon Locknut

Page 13

24.Remove the preattached 3 1/2” Pulleys (78) from the Offset Double “U”-bracket (61).

Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”-

bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).

25.Wrap the Swivel Cable (17) around a 3 1/2” Pulley

(78). Attach the Pulley and a Cable Trap (68) to the next to bottom hole in the Small Pulley Plates (31)

with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure the Cable Trap is turned to hold

the Cable in the groove of the Pulley.

26.Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) to the bracket on the Swivel Upright (5) with a 3/8” x 2”

Bolt (100) and a 3/8” Nylon Locknut (87).

Make

sure the Cable Trap is turned to hold the Cable

 

in the groove of the Pulley.

 

27. Attach the end of the Swivel Cable (17) to the

bracket on the Swivel Carriage (46) with a 3/8” x 1” Bolt (13) and a 3/8” Nylon Locknut (87).

28.Locate the Lat Cable (88), which is 89 1/4” long and has a ball on one end and an eyelet on the other. Route the eyelet end of the Cable up through the Butterfly Top Frame (7) and around a 3 1/2” Pulley (78). Attach the Pulley inside of the Butterfly

Top Frame with a 3/8” x 2 3/4” Bolt (101), two 3/8” Washers (91), two 1/2” Spacers (89), and a 3/8”

Nylon Locknut (87).

13

24

 

 

 

 

 

 

17

 

 

 

78

 

87

 

93

 

 

 

 

61

 

 

25

 

 

 

 

31

 

100

 

87

 

 

 

 

 

78

 

 

 

68

 

 

 

17

 

 

26

100

 

 

 

 

5

 

 

 

87

 

 

 

68

78

17

27

 

 

 

 

46

 

 

 

87

13

 

 

 

 

 

17

 

 

28

 

 

 

 

78

 

 

 

87

 

 

 

91

 

 

 

89

89

 

 

 

91

 

7

 

 

 

101

 

88

 

 

Image 13
Contents Serial Number Decal under seat Model No Serial NoPatent Pending Table of Contents Weight system in the location shown Important PrecautionsSure that the cables are on all of the pulleys DecalBefore YOU Begin Using the weight systemAssembly Them in place Nylon Locknuts Each Carriage Bolt. Do not tighten the Nylon Locknuts yetDo not tighten the Nylon Locknuts yet Two indicated 5/16 x 2 1/2 Carriage Bolts 110 Hole in the Swivel Upright AdjustmentLocknut 86 onto each Carriage Bolt En the Nylon Locknuts yetGrooved side is facing downward Make sureDo not tighten the Locknuts yet Must be able to pivot easily. R With the Bolt and a 3/8 Nylon Jamnut8 Nylon Jamnut 113 as shown EasilyLong and has an eyelet on each end Bolt 100 and a 3/8 Nylon Locknut Cable in the groove of the PulleyGroove of the Pulley Attach the end of the Swivel Cable 17 toPulley A 3/8 Nylon JamnutLocate the Butterfly Cable 69, which is Locknut 87. Make sure that the Long CableEd pin on the other end Locate the Leg Lever Cable 75, which isWasher 91, and a 3/8 Nylon Jamnut Upright 3 with a 3/8 x 3 3/4 Bolt 122, a 3/8End and a ball on the other end A 3/8 Nylon Locknut 119 122 121 113 Cage 120A 3/8 Nylon Locknut 120 With a 3/8 x 2 Bolt 100 and a 3/8 NylonNylon Locknut 120 OnlyA 3/8 Nylon Jamnut 124Nut 118 halfway onto the end A 3/8 Nylon LocknutNut against the 1/2 Washer 1. Rem Stack. Replace the PinNylon Locknuts yet Repeat this step with the other end of the Squat ArmTighten all of the 3/8 Nylon Locknuts 87 used in this step Backrest than the top. Attach the Squat Backrest to Press AdjustmentsIng any exercise 115 Adjusting the Squat ARM or Swivel CarriageLbs Top Weight Resistance ChartPulley and the Cable Trap between the higher set TroubleshootingButterfly Cable DiagramsSwivel High Cable Cable Leg LeverSwivel Low Full 90 DAY Warranty Bags, check to see if it has been pre-assembled X 3 3/4 Bolt R1202APage Round Inner Cap 2 x 2 Inner Cap 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key Qty Description Part LIST-Model NoExploded