Weider 831.153931 Two indicated 5/16 x 2 1/2 Carriage Bolts 110, En the Nylon Locknuts yet

Page 8

	7. Press a 2” x 3” Inner Cap (58) into the top of the	7
	Squat Upright (4). Slide the Squat Upright onto the	7
	Squat Upright (4). Slide the Squat Upright onto the	58
	two indicated 5/16” x 2 1/2” Carriage Bolts (110) in
	the Long Base (120). Finger tighten a 5/16” Nylon
	Locknut (86) onto each Carriage Bolt.	Do not tight-
	en the Nylon Locknuts yet.		58
			58
	Press a 2” x 3” Inner Cap (58) into the top of the	5
	Swivel Upright (5). Slide the Swivel Upright onto the
	two indicated 5/16” x 2 1/2” Carriage Bolts (110) in
	the Long Base (120). Finger tighten a 5/16” Nylon
	Locknut (86) onto each Carriage Bolt.	Do not tight-
	en the Nylon Locknuts yet.	4
		4
		86
		110	86
		120	86
			110
	8. Press two Swivel Bushings (66) into the Swivel	8
	Carriage (46).	8	66
	Carriage (46).		66
	Tighten an Adjustment Handle (65) into the Swivel
	Carriage (46). Orient the Swivel Carriage as shown.
	Slide the Carriage onto the Swivel Upright (5) and		46
	engage the Adjustment Handle into an adjustment		46
	engage the Adjustment Handle into an adjustment	65
	hole in the Swivel Upright.	65
	hole in the Swivel Upright.
		66
		5
		Adjustment
		Hole

8

Image 8

Contents Patent Pending Model No Serial NoSerial Number Decal under seat Table of Contents Important Precautions Weight system in the location shownSure that the cables are on all of the pulleys DecalUsing the weight system Before YOU BeginAssembly Them in place Do not tighten the Nylon Locknuts yet Each Carriage Bolt. Do not tighten the Nylon Locknuts yetNylon Locknuts Hole in the Swivel Upright Adjustment Two indicated 5/16 x 2 1/2 Carriage Bolts 110Locknut 86 onto each Carriage Bolt En the Nylon Locknuts yetMake sure Grooved side is facing downwardDo not tighten the Locknuts yet With the Bolt and a 3/8 Nylon Jamnut Must be able to pivot easily. R8 Nylon Jamnut 113 as shown EasilyLong and has an eyelet on each end Cable in the groove of the Pulley Bolt 100 and a 3/8 Nylon LocknutGroove of the Pulley Attach the end of the Swivel Cable 17 toA 3/8 Nylon Jamnut PulleyLocate the Butterfly Cable 69, which is Locknut 87. Make sure that the Long CableLocate the Leg Lever Cable 75, which is Ed pin on the other endUpright 3 with a 3/8 x 3 3/4 Bolt 122, a 3/8 Washer 91, and a 3/8 Nylon JamnutEnd and a ball on the other end A 3/8 Nylon Locknut 119 122 121 113 Cage 120With a 3/8 x 2 Bolt 100 and a 3/8 Nylon A 3/8 Nylon Locknut 120Only Nylon Locknut 120A 3/8 Nylon Jamnut 124A 3/8 Nylon Locknut Nut 118 halfway onto the endNut against the 1/2 Washer 1. Rem Stack. Replace the PinTighten all of the 3/8 Nylon Locknuts 87 used in this step Repeat this step with the other end of the Squat ArmNylon Locknuts yet Backrest than the top. Attach the Squat Backrest to Ing any exercise AdjustmentsPress Adjusting the Squat ARM or Swivel Carriage 115Weight Resistance Chart Lbs TopTroubleshooting Pulley and the Cable Trap between the higher setSwivel High Cable Cable DiagramsButterfly Swivel Low Leg LeverCable Full 90 DAY Warranty Bags, check to see if it has been pre-assembled R1202A X 3 3/4 BoltPage Round Inner Cap 2 x 2 Inner Cap 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Key Qty DescriptionExploded