Weider 831.153931 user manual Each Carriage Bolt. Do not tighten the Nylon Locknuts yet

Page 7

4.Press a 1 1/2” Square Inner Cap (67) into the square tube on the Butterfly Upright (3).

Slide the Butterfly Upright (3) onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Short Base

(2). Finger tighten a 5/16” Nylon Locknut (86) onto

each Carriage Bolt. Do not tighten the Nylon

Locknuts yet.

5.Press a 2” x 3” Inner Cap (58) into the top of the Seat Upright (9). Attach the Leg Lever Bumper (77) to the Seat Upright with a #10 x 1” Screw (14).

Slide the Seat Upright (9) onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86)

onto each Carriage Bolt. Do not tighten the Nylon

Locknuts yet.

6.Hold the Seat Frame (8) between the Seat Upright

(9)and the Butterfly Upright (3). Attach the Seat

Frame to the Seat Upright with two 5/16” x 3 3/4”

Bolts (92), two 5/16” Washers (90), and two 5/16”

Nylon Locknuts (86).	Do not tighten the Nylon
Locknuts yet.

Attach the Seat Frame (8) to the Butterfly Upright

(3)with two 5/16” x 3 3/4” Bolts (92), two 5/16” Washers (90), and two 5/16” Nylon Locknuts (86).

Do not tighten the Nylon Locknuts yet.

7

4
	67
	3
		86
	86
	2
		110
5	58
	58
77	9
14	86
	86	2
		2
	86
		110
6
	86
8		90
	86	92
	86
		90
90		3
90
92	9
92
	90

Image 7

Contents Serial Number Decal under seat Model No Serial NoPatent Pending Table of Contents Decal Important PrecautionsWeight system in the location shown Sure that the cables are on all of the pulleysBefore YOU Begin Using the weight systemAssembly Them in place Nylon Locknuts Each Carriage Bolt. Do not tighten the Nylon Locknuts yetDo not tighten the Nylon Locknuts yet En the Nylon Locknuts yet Hole in the Swivel Upright AdjustmentTwo indicated 5/16 x 2 1/2 Carriage Bolts 110 Locknut 86 onto each Carriage BoltGrooved side is facing downward Make sureDo not tighten the Locknuts yet Easily With the Bolt and a 3/8 Nylon JamnutMust be able to pivot easily. R 8 Nylon Jamnut 113 as shownLong and has an eyelet on each end Attach the end of the Swivel Cable 17 to Cable in the groove of the PulleyBolt 100 and a 3/8 Nylon Locknut Groove of the PulleyLocknut 87. Make sure that the Long Cable A 3/8 Nylon JamnutPulley Locate the Butterfly Cable 69, which isEd pin on the other end Locate the Leg Lever Cable 75, which isA 3/8 Nylon Locknut 119 122 121 113 Cage 120 Upright 3 with a 3/8 x 3 3/4 Bolt 122, a 3/8Washer 91, and a 3/8 Nylon Jamnut End and a ball on the other endA 3/8 Nylon Locknut 120 With a 3/8 x 2 Bolt 100 and a 3/8 Nylon124 OnlyNylon Locknut 120 A 3/8 Nylon JamnutStack. Replace the Pin A 3/8 Nylon LocknutNut 118 halfway onto the end Nut against the 1/2 Washer 1. RemNylon Locknuts yet Repeat this step with the other end of the Squat ArmTighten all of the 3/8 Nylon Locknuts 87 used in this step Backrest than the top. Attach the Squat Backrest to Press AdjustmentsIng any exercise 115 Adjusting the Squat ARM or Swivel CarriageLbs Top Weight Resistance ChartPulley and the Cable Trap between the higher set TroubleshootingButterfly Cable DiagramsSwivel High Cable Cable Leg LeverSwivel Low Full 90 DAY Warranty Bags, check to see if it has been pre-assembled X 3 3/4 Bolt R1202APage Round Inner Cap 2 x 2 Inner Cap 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key Qty Description Part LIST-Model NoExploded