Weider 831.153931 user manual Table of Contents

Page 2

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS	. . .	. . . . . . . .3
BEFORE YOU BEGIN	. . .	. . . . . . . . . . . .4
ASSEMBLY	.	. . . . . . . . . . . . . . . .5
ADJUSTMENTS	. .	. . . . . . . . . . . . .22
WEIGHT RESISTANCE CHART	. . . .	. . . . . . .24
TROUBLESHOOTING	. . .	. . . . . . . . . .25
CABLE DIAGRAMS	. .	. . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS	Back C	over
FULL 90 DAY WARRANTY		.Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly.

2

Image 2

Contents Patent Pending Model No Serial NoSerial Number Decal under seat Table of Contents Sure that the cables are on all of the pulleys Important PrecautionsWeight system in the location shown DecalUsing the weight system Before YOU BeginAssembly Them in place Do not tighten the Nylon Locknuts yet Each Carriage Bolt. Do not tighten the Nylon Locknuts yetNylon Locknuts Locknut 86 onto each Carriage Bolt Hole in the Swivel Upright AdjustmentTwo indicated 5/16 x 2 1/2 Carriage Bolts 110 En the Nylon Locknuts yetMake sure Grooved side is facing downwardDo not tighten the Locknuts yet 8 Nylon Jamnut 113 as shown With the Bolt and a 3/8 Nylon JamnutMust be able to pivot easily. R EasilyLong and has an eyelet on each end Groove of the Pulley Cable in the groove of the PulleyBolt 100 and a 3/8 Nylon Locknut Attach the end of the Swivel Cable 17 toLocate the Butterfly Cable 69, which is A 3/8 Nylon JamnutPulley Locknut 87. Make sure that the Long CableLocate the Leg Lever Cable 75, which is Ed pin on the other endEnd and a ball on the other end Upright 3 with a 3/8 x 3 3/4 Bolt 122, a 3/8Washer 91, and a 3/8 Nylon Jamnut A 3/8 Nylon Locknut 119 122 121 113 Cage 120With a 3/8 x 2 Bolt 100 and a 3/8 Nylon A 3/8 Nylon Locknut 120A 3/8 Nylon Jamnut OnlyNylon Locknut 120 124Nut against the 1/2 Washer 1. Rem A 3/8 Nylon LocknutNut 118 halfway onto the end Stack. Replace the PinTighten all of the 3/8 Nylon Locknuts 87 used in this step Repeat this step with the other end of the Squat ArmNylon Locknuts yet Backrest than the top. Attach the Squat Backrest to Ing any exercise AdjustmentsPress Adjusting the Squat ARM or Swivel Carriage 115Weight Resistance Chart Lbs TopTroubleshooting Pulley and the Cable Trap between the higher setSwivel High Cable Cable DiagramsButterfly Swivel Low Leg LeverCable Full 90 DAY Warranty Bags, check to see if it has been pre-assembled R1202A X 3 3/4 BoltPage Round Inner Cap 2 x 2 Inner Cap 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Key Qty DescriptionExploded