Weider 831.159833 user manual Arm Assembly

Page 12

Arm Assembly

18

90

11

 

18. Locate and open the parts bag labeled “ARM

 

67

 

 

 

78

ASSEMBLY.”

 

 

Press two 50mm Square Inner Caps (67) into the

 

13

Lubricate

ends of the Leg Lever (13).

 

 

 

 

 

Lubricate an M10 x 84mm Bolt (78) with grease.

 

67

 

Attach the Leg Lever (13) to the Butterfly Leg (11)

 

 

 

 

 

with the Bolt and an M10 Nylon Locknut (90). Do

 

 

 

not overtighten the Locknut; the Leg Lever

 

 

 

must be able to pivot easily.

 

 

 

19. Lubricate the M10 x 76mm Bolt (88) with grease.

19

 

 

Attach the Leg Press Lever (14) to the Press

 

 

 

 

 

Base (3) with the Bolt and an M10 Nylon Locknut

 

 

 

(90). Do not overtighten the Locknut; the Leg

 

14

 

Press Lever must pivot easily.

 

 

 

 

 

 

 

Lubricate

 

 

 

88

3

 

 

 

 

 

 

90

20. See the inset drawing. Press a Plastic Bushing

20

 

 

(60) onto each welded tube on the Press Frame

 

 

 

 

 

(17). Slide the Press Frame into place on the

 

 

 

Press Base (3). Note: This will be a tight fit; the

 

 

 

Plastic Bushings should fit onto each end of

 

 

 

the welded tubes in the Base.

 

106

 

Lubricate the M10 x 207mm Bolt (106) with

 

 

17

 

 

3

grease. Attach the Press Frame (17) to the Press

 

 

 

 

17

Base (3) with the Bolt and an M10 Nylon Locknut

 

 

 

 

 

(90). Do not overtighten the Locknut; the

 

Lubricate

90

Press Frame must pivot easily.

 

 

 

 

60

21. Press a 45mm Square Inner Cap (68) into the top

21

 

 

of a Press Arm (18). Press a 25mm Round Inner

 

 

 

 

 

Cap (66) into the Press Arm.

 

18

 

Attach the Press Arm (18) to the Press Frame

 

 

 

(17) with two M8 x 62mm Bolts (87) and two M8

 

 

 

Nylon Locknuts (86).

 

 

68

 

 

 

Repeat this step with the other Press Arm (18).

 

 

 

 

 

 

87

 

 

 

18

 

 

86

66

 

 

 

 

 

 

17

 

12

 

 

Image 12
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Before YOU Begin DecalAssembly Frame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yetPage Onto the Bolts. Do not tighten the Locknuts yet Locknuts 86. Do not tighten the Locknuts yetTighten the Locknuts yet Do not tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top Locknuts 90. Do not tighten the Locknuts yet Nylon Locknut 90. Do not tighten the LocknutIt. Do not tighten the Locknuts yet Arm Assembly AssemblyCable Assembly Cable AssemblyRepeat this step with the Left Butterfly Arm To the bracket on the back of the ButterflyRemove another V-pulley 34 from the bag Labeled Pulley BAG Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Page Attached as shown Trap is positioned to hold the Cable Groove of the PulleyCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Seat Assembly Locate and open the parts bag labeled SeatAttach the other Seat 23 to the Press Seat Frame 12, not shown in the same mannerPage Adjustments Attaching the AccessoriesAdjusting the LEG Press Plate Attaching the Curl PADChanging the Weight Setting Weight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Left Top BottomTroubleshooting and Maintenance Tightening the CablesPress Cable 72 can be tightened in the same manner Page Cable Diagrams Cable ID ChartPress Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Rear Cable Low CableButterfly Cable Ab Cable Part Identification CHART-Model No .159833 R1203A Page Page Part LIST-Model No Qty Description159833 Full 90-DAY Warranty Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL