61. Attach the Press Cable (72) to the remaining “U”- | 61 |
|
|
|
|
bracket (33) with an M8 Washer (100) and an M8 |
|
|
|
| |
|
|
|
|
| |
Nylon Locknut (86). Note: Do not completely | 72 |
|
|
| |
tighten the Locknut; it should be threaded |
| 96 |
| ||
onto the Cable so that only two threads show |
|
| 33 |
| |
|
|
|
| ||
past the Locknut (see the inset drawing). | 86 |
| 100 |
| |
| 43 |
|
| ||
Attach the |
| 86 |
| ||
|
| 72 | |||
Tube (43) with an M8 x 45mm Bolt (96) and an |
|
|
|
| |
|
|
|
|
| |
M8 Nylon Locknut (86). |
|
|
|
|
|
Important: Follow all five cables from end to |
|
|
|
|
|
end and make sure that they rest in the |
|
|
|
| 86 |
grooves of all of the pulleys and that the |
|
|
|
|
|
cables and the pulleys move smoothly. |
|
|
|
|
|
Seat Assembly | 62 |
|
|
|
|
|
|
|
|
| |
62. Locate and open the parts bag labeled “SEAT | 25 |
| 99 | 79 |
|
ASSEMBLY.” |
|
|
| ||
|
|
|
| ||
Attach the Butterfly Backrest (25) to the Butterfly |
|
| 4 |
|
|
|
|
|
|
| |
Upright (4) with two M6 x 65mm Bolts (79) and |
|
|
|
|
|
two M6 Washers (99). |
|
|
| 79 |
|
|
|
|
|
| |
|
|
| 99 |
|
|
63. Insert an M6 x 62mm Carriage Bolt (91) through | 63 |
|
|
|
|
the center hole in a Seat Plate (30). Using two |
|
|
|
| |
23 |
|
|
|
| |
M6 x 16mm Bolt (98), attach the Seat Plate to the |
|
|
|
|
|
Seat (23) with the serial number decal. |
|
|
|
|
|
Insert the M6 x 62mm Carriage Bolt (91) into the | Serial |
| 91 |
|
|
indicated hole in the Butterfly Seat Frame (10). | Number |
| 30 |
|
|
Secure the other end of the Seat (23) to the Seat | Decal |
|
|
| |
|
|
|
| ||
Frame with an M6 x 65mm Bolt (79) and an M6 |
|
| 98 |
|
|
Washer. Secure the M6 x 62mm Carriage Bolt |
|
|
|
| |
|
| 10 |
|
| |
with another M6 Washer (99) and an M6 Nylon |
|
|
|
|
|
Locknut (103). |
|
|
|
|
|
Attach the other Seat (23) to the Press Seat |
|
| 99 |
|
|
|
| 103 |
|
| |
Frame (12, not shown) in the same manner. |
|
| 79 |
|
|
64. Insert an M6 x 62mm Carriage Bolt (91) through | 64 |
|
|
|
|
the center hole in a Seat Plate (30). Attach the |
|
|
|
| |
|
|
|
| 79 | |
Seat Plate to the Press Backrest (24) with two M6 |
|
|
|
| |
|
|
|
| 99 | |
x 16mm Bolt (98). |
|
|
|
| |
24 |
|
| 5 |
| |
|
|
|
| ||
|
|
|
|
| |
Insert the M6 x 62mm Carriage Bolt (91) into the |
|
|
|
|
|
indicated hole in the Press Upright (5). Secure |
|
|
|
| 103 |
the other end of the Press Backrest (24) with an |
|
| 98 |
| |
30 |
|
| 99 | ||
M6 x 65mm Bolt (79) and an M6 Washer. Secure |
|
|
|
|
|
the M6 x 62mm Carriage Bolt with an M6 Washer |
|
|
|
|
|
(99) and an M6 Nylon Locknut (103). |
| 91 |
|
| |
|
|
|
| ||
| 23 |
|
|
|
|