Weider 831.159833 user manual

Page 7

4.Slide the Butterfly Upright (4) over the indicated M8 x 61mm Carriage Bolts (75) in the Butterfly Base (1). Hand tighten two M8 Nylon Locknuts (86) onto the Bolts. Do not tighten the Locknuts yet.

5.Press three 50mm Square Inner Caps (67) into the Butterfly Top Frame (7).

Attach the Butterfly Top Frame (7) to the indicat- ed bracket at the top of the Butterfly Upright (4) with two M8 x 66mm Bolts (89), a Medium Support Plate (109), and two M8 Nylon Locknuts (86). Do not tighten the Locknuts yet.

6.Press a 50mm Square Inner Cap (67) halfway into the top of the Butterfly Leg (11). Attach a Bumper (50) to the Butterfly Leg with an M4 x 25mm Screw (80).

Attach the Butterfly Seat Frame (10) to the Butterfly Leg (11) with two M8 x 66mm Bolts (89), two M8 Washers (100), and two M8 Nylon Locknuts (86). Do not tighten the Locknuts yet.

4

 

 

 

 

4

 

 

86

 

 

86

 

 

1

 

 

75

5

 

89

 

 

 

 

109

 

67

67

 

 

 

 

7

 

 

67

 

 

86

 

 

4

6

 

67

 

 

 

 

86

 

100

10

89

 

86

 

 

 

100

 

80

50

11

 

 

 

7

Image 7
Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginAssembly Locknuts yet Frame AssemblyFrame Assembly Locate and open the parts bag labeledPage Do not tighten the Locknuts yet Onto the Bolts. Do not tighten the Locknuts yetLocknuts 86. Do not tighten the Locknuts yet Tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top Nylon Locknut 90. Do not tighten the Locknut Locknuts 90. Do not tighten the Locknuts yetIt. Do not tighten the Locknuts yet Assembly Arm AssemblyTo the bracket on the back of the Butterfly Cable AssemblyCable Assembly Repeat this step with the Left Butterfly ArmIdentify the Rear Cable 70. It is approximately Remove another V-pulley 34 from the bag Labeled Pulley BAGIdentify the Ab Cable 74. It is approximately Page Trap is positioned to hold the Cable Groove of the Pulley Attached as shownCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Frame 12, not shown in the same manner Seat AssemblyLocate and open the parts bag labeled Seat Attach the other Seat 23 to the Press SeatPage Attaching the Curl PAD AdjustmentsAttaching the Accessories Adjusting the LEG Press PlateChanging the Weight Setting Bottom Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Lbs Left TopTightening the Cables Troubleshooting and MaintenancePress Cable 72 can be tightened in the same manner Page Cable ID Chart Cable DiagramsPress Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Low Cable Rear CableButterfly Cable Ab Cable Part Identification CHART-Model No .159833 R1203A Page Page Qty Description Part LIST-Model No159833 Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL Full 90-DAY Warranty