![](/images/new-backgrounds/1293232/29323229x1.webp)
29. Wrap the Rear Cable (70) under a 90mm Pulley | 29 |
|
|
|
|
(35). Attach the Pulley and a Cable Trap (38) to |
|
|
|
| |
|
|
|
|
| |
the top hole in the pair of Pulley Plates (32) with |
|
|
|
|
|
an M10 x 48mm Bolt (93) and an M10 Nylon |
|
|
|
|
|
Locknut (90). Make sure the Cable Trap is posi- |
|
|
|
|
|
tioned to hold the Cable in the groove of the |
|
|
|
|
|
Pulley. |
|
|
|
|
|
|
| 70 |
| 93 | |
|
|
|
|
| |
|
| 90 |
| 35 | 32 |
|
|
|
| ||
|
|
|
|
| |
|
| 32 | 38 |
| |
|
|
|
|
| |
30. Wrap the Rear Cable (70) over a 115mm Pulley | 30 |
|
|
|
|
(36) in the direction shown. Attach the Pulley |
|
|
|
| |
Bracket | 90 |
|
| ||
inside the indicated bracket on the Center Top |
|
|
|
|
|
Frame (8) with an M10 x 45mm Bolt (94) and an |
|
|
|
| 36 |
M10 Nylon Locknut (90). |
|
|
|
| |
|
|
|
| 94 | |
|
|
|
|
| |
|
| 8 |
|
|
|
|
|
|
| 70 |
|
31. Attach the end of the Rear Cable (70) to a “U”- | 31 |
|
|
|
|
bracket (33) with an M8 Washer (100) and an M8 |
|
|
|
| |
|
|
|
|
| |
Nylon Locknut (86). Do not completely tighten |
|
|
|
|
|
the Locknut; it should be tightened so that |
|
|
|
|
|
only two threads of the Cable show past the |
| 70 |
|
|
|
Locknut, as shown in the inset drawing. |
| 96 |
|
| |
|
|
|
| ||
Attach the | 33 |
| 100 |
| 70 |
Tube (44) with an M8 x 45mm Bolt (96) and an | 86 |
|
| ||
M8 Nylon Locknut (86). |
|
| 86 |
| 33 |
|
| 44 |
| ||
|
|
|
| ||
|
|
|
|
| 86 |
32. Identify the Ab Cable (74). It is approximately | 32 |
|
|
|
|
226 1/2” long, and it has a ball on one end and |
|
|
|
| |
|
|
|
|
| |
an eyelet on the other. |
|
|
| Large tabs | |
| 90 | 97 |
| ||
Wrap the Ab Cable (74) over a 90mm Pulley (35) |
| on this side | |||
|
| 39 |
| ||
as shown. Place two Pulley Covers (39) over the |
|
|
| ||
|
|
|
|
| |
Pulley, so that the large tabs are on the indicated |
| Pin |
|
| 39 |
side. Attach the Pulley and Pulley Covers to the |
|
|
|
| |
Butterfly Upright (4) with an M10 x 97mm Bolt |
| 4 |
|
| 77 |
(77), two M10 Washers (97), and an M10 Nylon |
| 35 |
| 97 | |
Locknut (90). Make sure the Cable is between |
|
| 74 | ||
|
|
|
| ||
the Pulley and the pin on the Upright. |
|
|
|
| |
|
|
|
|
|
15