7. Slide the Butterfly Leg (11) onto the two M8 x | 7 |
| 86 |
|
61mm Carriage Bolts (75) in the Butterfly Base |
|
| ||
| 10 | 89 | ||
(1). Hand tighten two M8 Nylon Locknuts (86) |
|
| ||
|
|
| ||
onto the Bolts. Do not tighten the Locknuts yet. |
|
|
|
|
Attach the Butterfly Seat Frame (10) to the |
|
| 86 | 100 |
|
|
| ||
Butterfly Upright (4) with two M8 x 66mm Bolts | 11 |
|
|
|
(89), two M8 Washers (100), and two M8 Nylon |
|
|
| |
|
| 4 |
| |
Locknuts (86). Do not tighten the Locknuts yet. |
|
|
| |
| 86 |
|
| |
| 86 |
|
| |
|
|
|
| |
|
|
| 1 |
|
|
|
| 75 |
|
8. Press a 25mm Square Inner Cap (69) into the | 8 |
|
|
|
small tube on the Press Upright (5). |
|
|
| |
|
|
|
| |
Slide the Press Upright (5) over the indicated M8 |
|
|
|
|
x 61mm Carriage Bolts (75) in the Press Base |
|
|
|
|
(3). Hand tighten two M8 Nylon Locknuts (86) |
| 5 |
|
|
onto the Bolts. Do not tighten the Locknuts yet. |
|
|
| |
Slide the Upright Support (6) over the M10 x |
|
|
|
|
63mm Carriage Bolt (76) and the M10 x 92mm |
|
| 86 |
|
Carriage Bolt (112) in the Press Base (3). Hand |
|
|
| |
|
|
|
| |
tighten an M10 Nylon Locknut (90) onto the M10 |
|
|
|
|
x 63mm Carriage Bolt. Do not tighten the |
|
|
|
|
Locknut yet. Note: Do not thread a locknut |
|
|
|
|
onto the M10 x 92mm Carriage Bolt yet. |
|
| 86 | 6 |
|
|
| ||
| 113 |
|
| |
Attach the Upright Support (6) to the Press |
|
|
| |
|
|
|
| |
Upright (5) with two M8 x 63mm Carriage Bolts |
|
|
|
|
(113) and two M8 Nylon Locknuts (86). Do not |
|
|
|
|
tighten the Locknuts yet. |
|
| 90 |
|
|
|
| 86 |
|
| 69 |
|
|
|
| 86 |
|
| 112 |
| 3 |
| 76 |
|
|
| 75 |
| |
|
|
|
| |
9. Press a 50mm Square Inner Cap (67) into the | 9 |
| 89 |
|
Press Seat Frame (12). Attach a Bumper (50) to |
|
| ||
|
|
| ||
|
|
| 86 | |
the Seat Frame with an M4 x 25mm Screw (80). |
| 12 |
| |
|
|
| ||
Slide the Press Seat Frame (12) onto the indicat- | 67 |
| 89 | 100 |
ed M8 x 61mm Carriage Bolts (75) in the Press |
|
| ||
|
|
|
| |
Base (3). Hand tighten two M8 Nylon Locknuts | 50 |
| 5 |
|
(86) onto the Bolts. Do not tighten the Locknuts |
|
| ||
80 | 86 |
| ||
yet. |
|
| ||
|
|
| ||
Attach the Press Seat Frame (12) to the Press | 86 |
|
|
|
|
|
|
| |
Upright (5) with two M8 x 66mm Bolts (89), two |
|
| 3 |
|
M8 Washers (100), and two M8 Nylon Locknuts |
| 75 |
| |
(86). Do not tighten the Locknuts yet. |
|
|
| |
| 8 |
|
|
|