Weider 831.159833 user manual Remove the M10 Nylon Locknut 90 used in step

Page 22

57.Remove the M10 Nylon Locknut (90) used in step 53.

Route the Press Cable (72) through the Press Frame (17).

Wrap the Press Cable (72) under a 90mm Pulley

(35).Slide a Cable Trap (38) and the Pulley onto the M10 x 121mm Bolt (102) in the bottom of the Press Upright (5). Properly tighten the M10 Nylon Locknut (90) onto the Bolt. Make sure the Cable

Trap is positioned to hold the Cable in the groove of the Pulley.

58.Wrap the Press Cable (72) around a 90mm Pulley

(35)as shown. Slide a Cable Trap (38) and the Pulley onto the M10 x 92mm Carriage Bolt (112) in the Press Base (3). Secure the Pulley with an M10 Nylon Locknut (90). Make sure the Cable

Trap is positioned to hold the Cable in the groove of the Pulley.

59.Lay the Press Cable (72) in the bracket on the Center Base (2). Attach a 90mm Pulley (35) inside the bracket with an M10 x 45mm Bolt (94) and an M10 Nylon Locknut (90).

60.Wrap the Press Cable (72) over a 115mm Pulley (36). Attach the Pulley inside the indicated bracket on the Center Top Frame (8) with an M10 x 45mm Bolt (94) and an M10 Nylon Locknut (90).

57

 

 

 

 

 

 

 

 

38

 

 

 

 

72

 

5

102

35

90

 

17

 

 

 

 

 

 

58

 

 

 

 

 

72

90

 

 

 

 

35

 

 

 

 

38

 

 

 

112

 

 

 

3

 

 

59

 

 

 

 

72

35

94

 

 

 

 

 

 

 

 

 

 

 

90

 

 

 

 

2

 

60

 

72

 

 

8

90

 

 

 

 

 

 

 

36

 

 

 

 

 

 

 

 

94

 

22

Image 22
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Before YOU Begin DecalAssembly Locate and open the parts bag labeled Frame AssemblyFrame Assembly Locknuts yetPage Tighten the Locknuts yet Onto the Bolts. Do not tighten the Locknuts yetLocknuts 86. Do not tighten the Locknuts yet Do not tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top Nylon Locknut 90. Do not tighten the Locknut Locknuts 90. Do not tighten the Locknuts yetIt. Do not tighten the Locknuts yet Arm Assembly AssemblyRepeat this step with the Left Butterfly Arm Cable AssemblyCable Assembly To the bracket on the back of the ButterflyRemove another V-pulley 34 from the bag Labeled Pulley BAG Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Page Attached as shown Trap is positioned to hold the Cable Groove of the PulleyCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Attach the other Seat 23 to the Press Seat Seat AssemblyLocate and open the parts bag labeled Seat Frame 12, not shown in the same mannerPage Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories Attaching the Curl PADChanging the Weight Setting Lbs Left Top Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever BottomTightening the Cables Troubleshooting and MaintenancePress Cable 72 can be tightened in the same manner Page Cable ID Chart Cable DiagramsPress Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Low Cable Rear CableButterfly Cable Ab Cable Part Identification CHART-Model No .159833 R1203A Page Page Part LIST-Model No Qty Description159833 Full 90-DAY Warranty Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL