Weider 831.159833 user manual

Page 9

10.Press a 50mm Square Inner Cap (67) into the Press Top Frame (9).

Attach the Press Top Frame (9) to the indicated bracket at the top of the Press Upright (5) with two M8 x 66mm Bolts (89), a Medium Support Plate (109), and two M8 Nylon Locknuts (86). Do not tighten the Locknuts yet.

11.Identify the Left Weight Guides (27), which have welded rings near the bottom. Slide two Weight Bumpers (46) onto the Left Weight Guides. Insert the Left Weight Guides into the indicated holes in the Center Base (2).

Set the other two Weight Bumpers (46) over the indicated holes in the Center Base (2). Insert the Right Weight Guides (26) through the Weight Bumpers and into the holes in the Center Base.

Make sure the oval holes on the Right Weight Guides are on the top.

12.Attach the indicated Weight Guides (26, 27) to the Center Base (2) with two M10 x 67mm Bolts (82), four M10 Washers (97), and two M10 Nylon Locknuts (90).

10

 

89

 

 

 

 

 

 

 

67

 

 

109

 

 

 

9

 

 

 

5

 

 

 

 

86

11

 

Oval

 

 

 

Holes

 

 

26

27

 

 

 

 

 

 

 

Welded

 

 

 

Rings

 

 

46

 

 

 

2

 

12

 

26

 

 

 

 

 

 

27

 

 

 

90

90

 

 

 

 

 

 

97

 

82

97

 

 

 

 

 

 

 

2

 

 

82

 

9

Image 9
Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginAssembly Frame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yetPage Locknuts 86. Do not tighten the Locknuts yet Onto the Bolts. Do not tighten the Locknuts yetTighten the Locknuts yet Do not tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top Locknuts 90. Do not tighten the Locknuts yet Nylon Locknut 90. Do not tighten the LocknutIt. Do not tighten the Locknuts yet Assembly Arm AssemblyCable Assembly Cable AssemblyRepeat this step with the Left Butterfly Arm To the bracket on the back of the ButterflyIdentify the Rear Cable 70. It is approximately Remove another V-pulley 34 from the bag Labeled Pulley BAGIdentify the Ab Cable 74. It is approximately Page Trap is positioned to hold the Cable Groove of the Pulley Attached as shownCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Locate and open the parts bag labeled Seat Seat AssemblyAttach the other Seat 23 to the Press Seat Frame 12, not shown in the same mannerPage Attaching the Accessories AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADChanging the Weight Setting Weight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top BottomTroubleshooting and Maintenance Tightening the CablesPress Cable 72 can be tightened in the same manner Page Cable Diagrams Cable ID ChartPress Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Rear Cable Low CableButterfly Cable Ab Cable Part Identification CHART-Model No .159833 R1203A Page Page Qty Description Part LIST-Model No159833 Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL Full 90-DAY Warranty