Weider 831.159833 user manual

Page 24

65.Press a 45mm Square Inner Cap (68) into the indicated end of the Adjustment Tube (15).

Orient the Leg Press Plate (16) and Adjustment Tube (15) as shown in the inset drawing. Attach the Adjustment Tube to the Leg Press Plate (16) with an M8 x 58mm Bolt (110), two M8 Washers (100), and an M8 Nylon Locknut (86).

Place the Adjustment Tube (15) in the bracket on top of the Leg Press Lever (14) and secure it with the Adjustment Pin (40).

66.Press four 19mm Round Inner Caps (64) into the ends of the two Pad Tubes (51).

Insert a Pad Tube (51) into the indicated hole in the Leg Lever (13). Slide two Foam Pads (52) onto the ends of the Pad Tube.

Insert a Pad Tube (51) into the welded tube on the Butterfly Leg (11). Slide two Foam Pads (52) onto the ends of the Pad Tube.

67.Attach the Curl Pad (22) to the Curl Post (21) with two M6 x 16mm Bolts (98).

65

 

 

 

 

110

15

 

 

100

40

 

 

 

 

 

 

68

 

 

 

14

 

100

86

16

15

16

 

 

 

66

 

 

 

64

 

 

 

 

52

 

 

 

51

 

64

 

 

 

 

 

 

52

 

13

 

 

 

11

 

 

 

 

 

64

67

 

 

 

 

22

 

98

 

 

 

 

21

 

 

68.Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page.

Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on pages 30 and 31 for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables; see TROUBLESHOOTING AND MAINTENANCE on page 28.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents
Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Before YOU Begin DecalAssembly Frame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yetPage Onto the Bolts. Do not tighten the Locknuts yet Locknuts 86. Do not tighten the Locknuts yetTighten the Locknuts yet Do not tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top Locknuts 90. Do not tighten the Locknuts yet Nylon Locknut 90. Do not tighten the LocknutIt. Do not tighten the Locknuts yet Arm Assembly AssemblyCable Assembly Cable AssemblyRepeat this step with the Left Butterfly Arm To the bracket on the back of the ButterflyRemove another V-pulley 34 from the bag Labeled Pulley BAG Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Page Attached as shown Trap is positioned to hold the Cable Groove of the PulleyCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Seat Assembly Locate and open the parts bag labeled SeatAttach the other Seat 23 to the Press Seat Frame 12, not shown in the same mannerPage Adjustments Attaching the AccessoriesAdjusting the LEG Press Plate Attaching the Curl PADChanging the Weight Setting Weight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Left Top BottomTroubleshooting and Maintenance Tightening the CablesPress Cable 72 can be tightened in the same manner Page Cable Diagrams Cable ID ChartPress Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Rear Cable Low CableButterfly Cable Ab Cable Part Identification CHART-Model No .159833 R1203A Page Page Part LIST-Model No Qty Description159833 Full 90-DAY Warranty Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL
Related manuals
Manual 37 pages 27.72 Kb