Weider 831.159833 user manual Remove the M10 Nylon Locknut 90 used in step

Page 19

45.Remove the M10 Nylon Locknut (90) used in step 43.

Wrap the Low Cable (71) under a 90mm Pulley (35). Attach the Pulley and a Cable Trap (38) to the M10 x 121mm Bolt (102) used in step 43 with the M10 Nylon Locknut (90). Make sure the

Cable Trap is positioned to hold the Cable in the groove of the Pulley.

46.Attach the Low Cable (71) to the Leg Lever (13) with an M8 x 68mm Shoulder Bolt (108), an M8 Washer (100), and an M8 Nylon Locknut (86).

Make sure that the flat side of the eyelet on the cable (see the inset drawing) is against the leg lever.

47.Identify the Press Cable (72). It is approximately 387 5/8” long and it has a ball on one end and a threaded shaft on the other.

Wrap the Press Cable (72) over a 90mm Pulley

(35).Attach the Pulley to the Press Top Frame (9) with an M10 x 89mm Bolt (111), an M10 Washer (97), and an M10 Nylon Locknut (90). Make sure the Cable is between the Pulley and the pin on the Press Top Frame.

48.Route the Press Cable (72) over the 90mm Pulley

(35)that was attached to the Press Top Frame (9) in step 16. Make sure the Cable Trap (38) is positioned to hold the Cable in the groove of the Pulley. Properly tighten the M10 Nylon Locknut (not shown) attached to the M10 x 97mm Bolt (77).

45
		71
4
	38
102		35	90
		35	90
46
100
86
13
		71	108
			108
			Flat
			Side
47
90	97
	9
	Pin	35	111
			111

	72
48
			38
	9		35
	9		77
			77
			72

19

Image 19

Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginAssembly Locknuts yet Frame AssemblyFrame Assembly Locate and open the parts bag labeledPage Do not tighten the Locknuts yet Onto the Bolts. Do not tighten the Locknuts yetLocknuts 86. Do not tighten the Locknuts yet Tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top Nylon Locknut 90. Do not tighten the Locknut Locknuts 90. Do not tighten the Locknuts yetIt. Do not tighten the Locknuts yet Assembly Arm AssemblyTo the bracket on the back of the Butterfly Cable AssemblyCable Assembly Repeat this step with the Left Butterfly ArmIdentify the Rear Cable 70. It is approximately Remove another V-pulley 34 from the bag Labeled Pulley BAGIdentify the Ab Cable 74. It is approximately Page Trap is positioned to hold the Cable Groove of the Pulley Attached as shownCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Frame 12, not shown in the same manner Seat AssemblyLocate and open the parts bag labeled Seat Attach the other Seat 23 to the Press SeatPage Attaching the Curl PAD AdjustmentsAttaching the Accessories Adjusting the LEG Press PlateChanging the Weight Setting Bottom Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Lbs Left TopTightening the Cables Troubleshooting and MaintenancePress Cable 72 can be tightened in the same manner Page Cable ID Chart Cable DiagramsPress Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Low Cable Rear CableButterfly Cable Ab Cable Part Identification CHART-Model No .159833 R1203A Page Page Qty Description Part LIST-Model No159833 Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL Full 90-DAY Warranty