Weider 831.159833 user manual Remove another V-pulley 34 from the bag Labeled Pulley BAG

Page 14

25. Wrap the Butterfly Cable (73) under a 90mm

25

 

 

Pulley (35). Attach the Pulley to the Double “U”-

 

 

 

 

 

bracket (31) with an M10 x 45mm Bolt (94) and

 

 

 

an M10 Nylon Locknut (90).

73

 

 

 

 

90

 

 

 

 

94

 

 

 

 

 

35

 

31

 

 

26. Remove another “V”-pulley (34) from the bag

26

 

 

labeled “PULLEY BAG 2.”

 

114

 

 

Wrap the Butterfly Cable (73) over the “V”-pulley

73

 

34

 

37

(34). Attach the “V”-pulley and a Long Cable Trap

 

 

 

 

 

 

(37) to the bracket on the back of the Butterfly

 

 

 

Upright (4) with an M10 x 58mm Bolt (114) and

 

 

 

an M10 Nylon Locknut (90). Make sure the Long

 

 

 

Cable Trap is oriented to hold the Cable in the

 

 

90

groove of the “V”-pulley.

 

 

 

 

 

 

 

4

27. Attach the Butterfly Cable (73) to the bracket on

27

 

 

the Right Butterfly Arm (19) with an M8 x 20mm

 

 

86

 

 

Shoulder Bolt (84) and an M8 Nylon Locknut (86).

 

 

 

 

 

Make sure that the flat side of the eyelet on

 

 

 

the cable (see the inset drawing) is against

 

 

 

theButterfly Arm.

19

 

 

 

 

 

 

73

 

 

 

84

 

 

 

 

 

Flat

 

 

 

Side

28. Identify the Rear Cable (70). It is approximately

28

 

 

95 1/8” long, and it has an eyelet on one end and

 

 

90

97

 

a threaded shaft on the other.

8

Attach the eyelet on the Rear Cable (70) inside

 

 

97

 

 

82

the Center Top Frame (8) with an M10 x 67mm

 

 

 

 

 

Bolt (82), two M10 Washers (97), and an M10

 

 

 

Nylon Locknut (90).

 

 

 

 

 

 

70

 

14

 

 

Image 14
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Before YOU Begin DecalAssembly Locate and open the parts bag labeled Frame AssemblyFrame Assembly Locknuts yetPage Tighten the Locknuts yet Onto the Bolts. Do not tighten the Locknuts yetLocknuts 86. Do not tighten the Locknuts yet Do not tighten the Locknuts yetPage Weight Guides 26. Note Make sure the Top It. Do not tighten the Locknuts yet Locknuts 90. Do not tighten the Locknuts yetNylon Locknut 90. Do not tighten the Locknut Arm Assembly AssemblyRepeat this step with the Left Butterfly Arm Cable AssemblyCable Assembly To the bracket on the back of the ButterflyRemove another V-pulley 34 from the bag Labeled Pulley BAG Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Page Attached as shown Trap is positioned to hold the Cable Groove of the PulleyCable Guide 102 Remove the M10 Nylon Locknut 90 used in step Page Page Remove the M10 Nylon Locknut 90 used in step Attach the other Seat 23 to the Press Seat Seat AssemblyLocate and open the parts bag labeled Seat Frame 12, not shown in the same mannerPage Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories Attaching the Curl PADChanging the Weight Setting Lbs Left Top Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever BottomPress Cable 72 can be tightened in the same manner Troubleshooting and MaintenanceTightening the Cables Page Press Cable 70, 95 1/8 71, 132 2/8 74, 226 1/2 72, 387 5/8 Cable DiagramsCable ID Chart Butterfly Cable Ab Cable Rear CableLow Cable Part Identification CHART-Model No .159833 R1203A Page Page Part LIST-Model No Qty Description159833 Full 90-DAY Warranty Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL