Weider 831.159830 user manual

Page 18

41.Locate the Weight Plate (48) that is attached to the bottom of the Bottom Weight (47).

See the inset drawing. Attach the end of the Ab Cable (74) to the bottom of the Weight Plate (48) with a 5/16” x 1 3/4” Bolt (96) and a 5/16” Nylon Locknut (86).

42.Remove a Pro Pulley (110) from the bag labeled “PULLEY BAG 2.”

Identify the Low Cable (71). It is approximately 142 1/8” long and it has a ball on one end and an eyelet on the other. Route the eyelet end through the slot in the cable guide on the Butterfly Base

Route the Low Cable (71) under the Pro Pulley

(110).Attach the Pro Pulley and a Cable Trap

(38)to the bracket on the Butterfly Base (1) with a 3/8” x 2” Bolt (93) and a 3/8” Nylon Locknut

(90).Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

43.Wrap the Low Cable (71) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and a Cable Trap (38) to the indicated hole in the Butterfly Upright (4) with a 3/8” x 4 3/4” Bolt (102) and a 3/8” Nylon Jamnut (92). Note: Thread the

Jamnut only two turns onto the Bolt, another Pulley will be attached to the Bolt in step 45. Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

44.Wrap the Low Cable (71) over a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and a Cable Trap (38) to the forth set of holes from the bottom in the Pulley Plates (32) with a 3/8” x 2” Bolt (93) and a 3/8” Nylon Locknut (90). Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

41
86
48
	96	47
74
42
93	110
	38
71
			90
		1
Cable
Guide
43	102
	102
		35
	71	38
		4	92
		4
44
	32
	90	93
	38	35
	38
	71

18

Image 18

Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin DecalAssembly Make Assembly Easier for YourselfFrame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yet Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories to a Pulley Station Attaching the Curl PADDo not tighten the Nylon Locknuts yet On the Short Weight Tube Guides 26. Make sure the Weights are turnedGuides 26. Note Make sure the Top Weight is Weights are turned so the pin grooves are On the bottomNylon Locknuts yet Must be behind the Center Top Frame, as Shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Jamnuts 92. Do not tighten the Nylon Locknuts yetLocate and open the parts bag labeled ARM Arm AssemblyAssembly Tighten the Nylon Jamnut the Press FrameBack of the Butterfly Upright 4 with a 3/8 Cable AssemblyPages 30 Identify the Butterfly Cable 73. It is approxi Make sure the Long Cable Trap is oriented as ShownMake sure the Long Cable Trap is orient Ed as shown Remove another V-Pulley 34 from the bag Labeled Pulley BAGOn the back of the Butterfly Upright 4 with a Identify the Rear Cable 70. It is approximatelyTrap is positioned to hold the Cable Groove of the Pulley Identify the Ab Cable 74. It is approximatelyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Seat Assembly Locate and open the parts bag labeled SeatLeg Press Plate 16 must be on the upper edge Tighten the Nylon Locknuts yet Do not tighten the 5/16 Nylon Locknuts YetOnto the Bolts. Do not tighten the Nylon Locknuts yet Locknuts 86. Do not tighten the Nylon Locknuts yetChanging the Weight Setting Lbs Left Top Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever BottomTroubleshooting and Maintenance Tightening the CablesPage Cable Diagrams Cable ID ChartPress Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY WarrantyModel No SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Part LIST-Model No Qty DescriptionDRAWING-Model No