Weider 831.159830 user manual 102

Page 21

53.Wrap the Press Cable (72) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and a Cable Trap (38) to the indicated hole on the right side of the Press Upright (5) with a 3/8” x 4 3/4” Bolt (102) and a 3/8” Nylon Jamnut (92).

Note: Thread the Jamnut only two turns onto the Bolt; another Pulley will be attached to the Bolt in step 57. Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

54.Route the Press Cable (72) through the Press Frame (17) and around a 3 1/2” Pulley (35) as shown. Attach the Pulley and a Cable Trap (38) to the indicated hole on the right side of the Leg Press Lever (14) with a 3/8” x 4 3/4” Bolt (102) and a 3/8” Nylon Jamnut (92). Note: Thread the

Jamnut only two turns onto the Bolt; another Pulley will be attached to the Bolt in step 56. Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

55.Wrap the Press Cable (72) around a “V”-Pulley

(34)in the direction shown. Attach the Pulley and a Long Cable Trap (37) underneath the Press Seat Frame (12) with a 3/8” x 4 1/4” Bolt (85), a 3/8” Washer (97), and a 3/8” Nylon Locknut (90).

Note: the Press Seat Frame has five adjust- ment holes. Attach the Pulley to the second hole from the Leg Press Lever (14). Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

56.Remove the 3/8” Nylon Jamnut (92) used in step 54.

Wrap the Press Cable (72) around a 3 1/2” Pulley

(35)in the direction shown. Slide a Cable Trap

(38)and the Pulley onto the 3/8” x 4 3/4” Bolt

(102)in the Leg Press Lever (14). Properly tight- en the 3/8” Nylon Jamnut (92) onto the Bolt.

Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

53

 

 

 

102

92

 

72

 

 

 

35

5

 

 

 

 

38

54

 

 

102

72

 

35

38

92

 

 

 

14

 

55

 

 

 

85

 

 

97

 

 

12

38

 

72

34

14

90

 

56

 

 

 

14

 

102

 

 

 

92 72

 

 

38 35

21

Image 21
Contents SEARS, Roebuck and CO. Hoffman ESTATES, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyFrame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yet Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADDo not tighten the Nylon Locknuts yet Guides 26. Note Make sure the Top Weight is Guides 26. Make sure the Weights are turnedOn the Short Weight Tube Weights are turned so the pin grooves are On the bottomLocknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as Shown in stepNylon Locknuts yet Nylon Jamnuts 92. Do not tighten the Nylon Locknuts yetAssembly Arm AssemblyLocate and open the parts bag labeled ARM Tighten the Nylon Jamnut the Press FramePages 30 Identify the Butterfly Cable 73. It is approxi Cable AssemblyBack of the Butterfly Upright 4 with a 3/8 Make sure the Long Cable Trap is oriented as ShownOn the back of the Butterfly Upright 4 with a Remove another V-Pulley 34 from the bag Labeled Pulley BAGMake sure the Long Cable Trap is orient Ed as shown Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Trap is positioned to hold the Cable Groove of the PulleyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Onto the Bolts. Do not tighten the Nylon Locknuts yet Do not tighten the 5/16 Nylon Locknuts YetTighten the Nylon Locknuts yet Locknuts 86. Do not tighten the Nylon Locknuts yetChanging the Weight Setting Weight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top BottomTightening the Cables Troubleshooting and MaintenancePage Cable Diagrams Cable ID ChartPress Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Model No Full 90 DAY WarrantySEARS, Roebuck and CO., Hoffman ESTATES, IL SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part LIST-Model NoDRAWING-Model No