Weider 831.159830 user manual

Page 29

Slack can be removed from the Press Cable (72) by moving the “V”-Pulley (34) attached to the Press Seat Frame (12) closer to the Press Upright (5).

Remove the 3/8” x 4 1/4” Bolt (85), 3/8” Washer (97), and 3/8” Nylon Locknut (90) from the Press Seat Frame (12), the “V”-Pulley (34), and the Long Cable Trap (37). Move the Pulley to a hole that is closer to the Press Upright (5), one hole at a time, until the slack is removed. Reattach the Pulley and Cable Trap to the hole with the Bolt, Washer, and Nylon Locknut.

If there is still slack in the Press Cable (72), move the “V”-Pulley (34) attached to the small tube on the Press Upright (5) to a hole that is closer to the Upright.

Remove the 3/8” x 3 1/4” Bolt (104), 3/8” Washer (97), and 3/8” Nylon Locknut (90) from the Press Upright (5), the “V”-Pulley (34), and the Long Cable Trap (37). Move the Pulley to a hole that is closer to the Press Upright, one hole at a time, until the slack is removed. Reattach the Pulley and Cable Trap to the hole with the Bolt, Washer, and Nylon Locknut.

	85
	97
12	37
12
72	34
90
90
97
34
72	5
104

If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

29

Image 29

Contents SEARS, Roebuck and CO. Hoffman ESTATES, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyLocate and open the parts bag labeled Frame AssemblyFrame Assembly Locknuts yet Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADDo not tighten the Nylon Locknuts yet Guides 26. Note Make sure the Top Weight is Guides 26. Make sure the Weights are turnedOn the Short Weight Tube Weights are turned so the pin grooves are On the bottomLocknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as Shown in stepNylon Locknuts yet Nylon Jamnuts 92. Do not tighten the Nylon Locknuts yetAssembly Arm AssemblyLocate and open the parts bag labeled ARM Tighten the Nylon Jamnut the Press FramePages 30 Identify the Butterfly Cable 73. It is approxi Cable AssemblyBack of the Butterfly Upright 4 with a 3/8 Make sure the Long Cable Trap is oriented as ShownOn the back of the Butterfly Upright 4 with a Remove another V-Pulley 34 from the bag Labeled Pulley BAGMake sure the Long Cable Trap is orient Ed as shown Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Trap is positioned to hold the Cable Groove of the PulleyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Onto the Bolts. Do not tighten the Nylon Locknuts yet Do not tighten the 5/16 Nylon Locknuts YetTighten the Nylon Locknuts yet Locknuts 86. Do not tighten the Nylon Locknuts yetChanging the Weight Setting Weight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top BottomTightening the Cables Troubleshooting and MaintenancePage Press Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Cable DiagramsCable ID Chart Low Cable Rear Cable Ab Cable Butterfly Cable Model No Full 90 DAY WarrantySEARS, Roebuck and CO., Hoffman ESTATES, IL SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part LIST-Model NoDRAWING-Model No