Weider 831.159830 user manual Do not tighten the Nylon Locknuts yet

Page 9

10.Press a 2” Square Inner Cap (67) into the Press Top Frame (9).

Attach the Press Top Frame (9) to the indicated bracket at the top of the Press Upright (5) with two 5/16” x 2 3/4” Bolts (89), a Medium Support Plate (109), and two 5/16” Nylon Locknuts (86).

Do not tighten the Nylon Locknuts yet.

11.Identify the Left Weight Guides (27), which have welded rings near the bottom. Slide two Weight Bumpers (46) onto the Left Weight Guides. Note:

The wide end of the Weight Bumpers must be on bottom. Insert the Left Weight Guides into the indicated holes in the Center Base (2).

Set the other two Weight Bumpers (46) over the indicated holes in the Center Base (2). Note: The wide end of the Weight Bumpers must be on bottom. Insert the Right Weight Guides (26) through the Weight Bumpers and into the holes in the Center Base.

12.Attach the indicated Weight Guides (26, 27) to the Center Base (2) with two 3/8” x 2 3/4” Bolts (82), four 3/8” Washers (97), and two 3/8” Nylon Locknuts (90).

10		89
		89
			67
		109
		9
		5
			86
11
	26	27
	26
			Welded
			Rings
		46
		2
12		26
		26
		27
		90	90
			90
			97
	82	97
	82
			2
		82

9

Image 9

Contents SEARS, Roebuck and CO. Hoffman ESTATES, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyFrame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yet Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADDo not tighten the Nylon Locknuts yet Guides 26. Note Make sure the Top Weight is Guides 26. Make sure the Weights are turnedOn the Short Weight Tube Weights are turned so the pin grooves are On the bottomLocknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as Shown in stepNylon Locknuts yet Nylon Jamnuts 92. Do not tighten the Nylon Locknuts yetAssembly Arm AssemblyLocate and open the parts bag labeled ARM Tighten the Nylon Jamnut the Press FramePages 30 Identify the Butterfly Cable 73. It is approxi Cable AssemblyBack of the Butterfly Upright 4 with a 3/8 Make sure the Long Cable Trap is oriented as ShownOn the back of the Butterfly Upright 4 with a Remove another V-Pulley 34 from the bag Labeled Pulley BAGMake sure the Long Cable Trap is orient Ed as shown Identify the Rear Cable 70. It is approximatelyIdentify the Ab Cable 74. It is approximately Trap is positioned to hold the Cable Groove of the PulleyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Onto the Bolts. Do not tighten the Nylon Locknuts yet Do not tighten the 5/16 Nylon Locknuts YetTighten the Nylon Locknuts yet Locknuts 86. Do not tighten the Nylon Locknuts yetChanging the Weight Setting Weight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top BottomTightening the Cables Troubleshooting and MaintenancePage Cable Diagrams Cable ID ChartPress Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Model No Full 90 DAY WarrantySEARS, Roebuck and CO., Hoffman ESTATES, IL SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part LIST-Model NoDRAWING-Model No