Weider 831.159830 user manual

Page 19

45.Remove the 3/8” Nylon Jamnut (92) from the 3/8” x 4 3/4” Bolt (102) inserted into the Butterfly Upright (4) in step 43.

Wrap the Low Cable (71) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and a Cable Trap (38) to the 3/8” x 4 3/4” Bolt (102) with the 3/8” Nylon Jamnut (92). Make sure the

Cable Trap is positioned to hold the Cable in the groove of the Pulley.

46.Attach the Low Cable (71) to the Leg Lever (13) with a 5/16” x 2 3/4” Shoulder Bolt (108), a 5/16” Washer (100), and a 5/16” Nylon Jamnut (77).

47.Remove a Pro Pulley (110) from the bag labeled “PULLEY BAG 2.”

Identify the Press Cable (72). It is approximately 387 5/8” long and it has a ball on one end and a threaded shaft on the other.

Wrap the Press Cable (72) around the Pro Pulley

(110)in the direction shown. Attach the Pulley to the Press Top Frame (9) with a 3/8” x 3 1/2” Bolt (111), a 3/8” Washer (97), and a 3/8” Nylon Jamnut (92). Make sure the Cable is between the Pulley and the pin on the Press Top Frame.

48.Route the threaded end of the Press Cable (72) around the 3 1/2” Pulley (35) that was attached to the Press Top Frame (9) in step 16. Make sure the Cable Trap (38) is positioned to hold the Cable in the groove of the Pulley. Properly tighten the 3/8” Nylon Locknut (not shown) attached to the 3/8” x 4” Bolt (78).

45

 

 

 

 

 

71

 

4

 

 

 

 

38

 

 

102

35

92

 

 

46

 

 

 

100

 

 

 

77

 

 

 

13

 

 

 

 

 

 

108

 

 

71

 

47

 

 

 

92

97

 

 

 

9

 

 

 

Pin

110

111

 

 

 

 

 

 

72

 

 

48

 

 

 

 

 

 

38

 

9

 

35

 

 

78

 

 

 

 

 

 

72

19

Image 19
Contents SEARS, Roebuck and CO. Hoffman ESTATES, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyFrame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yet Attaching the Curl PAD AdjustmentsAttaching the Accessories to a Pulley Station Adjusting the LEG Press PlateDo not tighten the Nylon Locknuts yet Weights are turned so the pin grooves are On the bottom Guides 26. Make sure the Weights are turnedGuides 26. Note Make sure the Top Weight is On the Short Weight TubeNylon Jamnuts 92. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as Shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Locknuts yetTighten the Nylon Jamnut the Press Frame Arm AssemblyAssembly Locate and open the parts bag labeled ARMMake sure the Long Cable Trap is oriented as Shown Cable AssemblyPages 30 Identify the Butterfly Cable 73. It is approxi Back of the Butterfly Upright 4 with a 3/8Identify the Rear Cable 70. It is approximately Remove another V-Pulley 34 from the bag Labeled Pulley BAGOn the back of the Butterfly Upright 4 with a Make sure the Long Cable Trap is orient Ed as shownIdentify the Ab Cable 74. It is approximately Trap is positioned to hold the Cable Groove of the PulleyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Locknuts 86. Do not tighten the Nylon Locknuts yet Do not tighten the 5/16 Nylon Locknuts YetOnto the Bolts. Do not tighten the Nylon Locknuts yet Tighten the Nylon Locknuts yetChanging the Weight Setting Bottom Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Lbs Left TopTightening the Cables Troubleshooting and MaintenancePage Cable ID Chart Cable DiagramsPress Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No SEARS, Roebuck and CO., Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part LIST-Model NoDRAWING-Model No