Weider 831.159830 user manual Adjustments, Attaching the Accessories to a Pulley Station

Page 8

ADJUSTMENTS

The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR-

TANT: When using an accessory, make sure it is in the correct starting position for the exercise to be performed. If there is any slack in the cables or chain as an exercise is performed, the effectiveness of the exercise will be reduced.

ATTACHING THE ACCESSORIES TO A PULLEY STATION

Attach the Lat Bar (59) to the Low Cable (71) at the low pulley station with a Cable Clip (58). For some exercises, the Chain (57) should be attached between the Lat Bar and the Low Cable with two Cable Clips.

Adjust the length of the Chain between the Lat Bar and the Low Cable so the Lat Bar is in the correct starting position for the exercise to be performed.

The Nylon Strap (83) or Ab Strap (56) can be attached in the same manner. The accessories can be attached to the ab pulley station or high pulley station in the same manner.

ADJUSTING THE LEG PRESS PLATE

To adjust the position of the Leg Press Plate (16), pull out the Adjustment Pin (40) and slide the Adjustment Tube (15) either backward or forward in the bracket on the Leg Press Lever (14). Line up one of the adjustment holes in the Adjustment Tube with the hole in the bracket and re-insert the Adjustment Pin.

ATTACHING THE CURL PAD

To use the Curl Pad (22), remove the 2” Square Inner Cap (67) from the Butterfly Leg (11). Slide the Curl Post (21) to the desired height in the Butterfly Leg. Tighten the Curl Knob (49) into the Butterfly Leg and an adjustment hole in the Curl Post.

83

71

58

57

58

 

59

56

 

40

 

15

 

16

 

14

 

22

 

21

49

 

67

 

11

 

25

 

Image 8
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin DecalAssembly Make Assembly Easier for YourselfLocate and open the parts bag labeled Frame AssemblyFrame Assembly Locknuts yet Adjustments Attaching the Accessories to a Pulley StationAdjusting the LEG Press Plate Attaching the Curl PADDo not tighten the Nylon Locknuts yet Guides 26. Make sure the Weights are turned Guides 26. Note Make sure the Top Weight isOn the Short Weight Tube Weights are turned so the pin grooves are On the bottomMust be behind the Center Top Frame, as Shown in step Locknuts 90. Do not tighten the Nylon Locknuts yetNylon Locknuts yet Nylon Jamnuts 92. Do not tighten the Nylon Locknuts yetArm Assembly AssemblyLocate and open the parts bag labeled ARM Tighten the Nylon Jamnut the Press FrameCable Assembly Pages 30 Identify the Butterfly Cable 73. It is approxiBack of the Butterfly Upright 4 with a 3/8 Make sure the Long Cable Trap is oriented as ShownRemove another V-Pulley 34 from the bag Labeled Pulley BAG On the back of the Butterfly Upright 4 with aMake sure the Long Cable Trap is orient Ed as shown Identify the Rear Cable 70. It is approximatelyTrap is positioned to hold the Cable Groove of the Pulley Identify the Ab Cable 74. It is approximatelyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Seat Assembly Locate and open the parts bag labeled SeatLeg Press Plate 16 must be on the upper edge Do not tighten the 5/16 Nylon Locknuts Yet Onto the Bolts. Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts yet Locknuts 86. Do not tighten the Nylon Locknuts yetChanging the Weight Setting Weight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Left Top BottomTroubleshooting and Maintenance Tightening the CablesPage Press Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Cable DiagramsCable ID Chart Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Hoffman ESTATES, IL SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Part LIST-Model No Qty DescriptionDRAWING-Model No