Weider 831.159830 user manual Locknuts yet

Page 7

4.Slide the Butterfly Upright (4) over the indicated 5/16” x 2 1/2” Carriage Bolts (75) in the Butterfly Base (1). Hand tighten two 5/16” Nylon Locknuts (86) onto the Bolts. Do not tighten the Nylon

Locknuts yet.

5.Press three 2” Square Inner Caps (67) into the Butterfly Top Frame (7). Press two Round Inner Caps (63) into the top of the Butterfly Top Frame.

Attach the Butterfly Top Frame (7) to the indicat- ed bracket at the top of the Butterfly Upright (4) with two 5/16” x 2 3/4” Bolts (89), a Medium Support Plate (109), and two 5/16” Nylon Locknuts (86).

6.Press a 2” Square Inner Cap (67) halfway into the top of the Butterfly Leg (11). Attach a Bumper (50) to the Butterfly Leg with a 1” Tap Screw (80).

Attach the Butterfly Seat Frame (10) to the Butterfly Leg (11) with two 5/16” x 2 3/4” Bolts (89), two 5/16” Washers (100), and two 5/16” Nylon Locknuts (86). Do not tighten the Nylon

Locknuts yet.

4
			4
			86
			86
			1
			75
5			89
			89
			109
			63
	67		67
	67
		7	63
		7
			67
			86
			4
6			67
			67
			86
	100		10
89			86
89
	100
80	50		11
80

7

Image 7

Contents SEARS, Roebuck and CO. Hoffman ESTATES, IL Model No Serial NoTable of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyFrame Assembly Frame AssemblyLocate and open the parts bag labeled Locknuts yet Attaching the Curl PAD AdjustmentsAttaching the Accessories to a Pulley Station Adjusting the LEG Press PlateDo not tighten the Nylon Locknuts yet Weights are turned so the pin grooves are On the bottom Guides 26. Make sure the Weights are turnedGuides 26. Note Make sure the Top Weight is On the Short Weight TubeNylon Jamnuts 92. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as Shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Locknuts yetTighten the Nylon Jamnut the Press Frame Arm AssemblyAssembly Locate and open the parts bag labeled ARMMake sure the Long Cable Trap is oriented as Shown Cable AssemblyPages 30 Identify the Butterfly Cable 73. It is approxi Back of the Butterfly Upright 4 with a 3/8Identify the Rear Cable 70. It is approximately Remove another V-Pulley 34 from the bag Labeled Pulley BAGOn the back of the Butterfly Upright 4 with a Make sure the Long Cable Trap is orient Ed as shownIdentify the Ab Cable 74. It is approximately Trap is positioned to hold the Cable Groove of the PulleyTrap is positioned to hold the Cable Groove of the Pulley Locknut 90. Make sure the Cable is routed Direction shown Page Page Page 102 Page Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Locknuts 86. Do not tighten the Nylon Locknuts yet Do not tighten the 5/16 Nylon Locknuts YetOnto the Bolts. Do not tighten the Nylon Locknuts yet Tighten the Nylon Locknuts yetChanging the Weight Setting Bottom Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Lbs Left TopTightening the Cables Troubleshooting and MaintenancePage Cable ID Chart Cable DiagramsPress Cable 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No SEARS, Roebuck and CO., Hoffman ESTATES, ILPage Page Part Identification CHART-Model No .159830 R0402A Page Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part LIST-Model NoDRAWING-Model No