Weider WESY59101 user manual Trap is turned to hold the Cable in place, Hold the Cable in place

Page 12

23.Remove the preassembled 3/8” x 2” Bolts (54) from one set of Adjustable Pulley Plates (23).

Wrap the Butterfly Cable (73) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable Trap (25) between the top holes of the Adjustable

Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a

3/8” Nylon Locknut (50). Be sure that the Cable

Trap is turned to hold the Cable in place.

24.Wrap the Butterfly Cable (73) around a “V”-Pulley

(27).Attach the “V”-Pulley and a Large Cable Trap

(32)to the bracket on the Butterfly Upright (1) with

a 3/8” x 2 1/2” Bolt (87) and a 3/8” Nylon Locknut (50). Be sure that the Cable Trap is turned to

hold the Cable in place.

25.Attach the Butterfly Cable (73) to the Left Pivot Arm

(71)with a 5/16” x 2 1/4” Shoulder Bolt (79) and a 5/16” Nylon Jamnut (101).

26. Locate the Ab Cable (47). Insert the Ab Cable up through the Press Top Frame (9) and wrap it

around a 3 1/2” Pulley (24). Attach a 3/8” Flat Washer (48) and a 5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press Top Frame and the 3 1/2” Pulley. Secure

another 5/8” x 3/4” Bushing and 3/8” Flat Washer to the Bolt with a 3/8” Nylon Locknut (50).

12

	23
	54	24
	25	24
		73
		50
	23
	24	87
		87
	32
	50	27
	50
		73
		1
	25
	73
		79
		71
		101
	26
	66
	24
	62	9
	48	9
	48
	48	50
	47

Image 12

Contents QUESTIONS? Model No. WESY59101 Serial NoSerial Number Decal Under Seat Customer HOT LineTable of Contents Limited WarrantyImportant Precautions Replacement decal Apply the decal in the location shownMake sure all parts are properly tightened Ing down Decal shownUsing the weight system Before YOU BeginFor your benefit, read this manual carefully before DecalAssembly Cable AssemblyArm Assembly To open the parts bag for that stageFrame Assembly AssemblyDo not tighten the Nylon Locknuts yet Press the Weight Tube Bumper 18 into the Weight Tube See the inset drawingCorner bar of the Press Base SlotARM Assembly Locknuts 50. Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts used in steps Bolt and a 3/8 Nylon Locknut HandlesCable Assembly Able to pivot easilyInsert two 2 Square Inner Caps 28 into the Leg Lever 101Trap is turned to hold the Cable in place Hold the Cable in placeFrame 9. Attach a 3/8 Flat Washer 48 and a Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8Nylon Locknut Wrap the Ab Pulley 47 around another 3 1/2Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 PulleyWrap the Weight Cable 72 around a 3 1/2 Pulley Cable Trap is turned to hold the Cable in place4 Bolt 57 and a 3/8 Nylon Jamnut Cable in placeBe sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 BoltsDo not tighten the Nylon Locknut yet To hold the Cable in place Be surePlace Hold the Cable 75 in placeSeat Assembly Locate and open the parts bag labeled Seat AssemblyADJUSTMENTS, beginning on page 21 of this manual Maintenance onWelded Adjustments Attaching the LAT BAR or AB Strap to High Pulley StationAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or NylonAdjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Troubleshooting and Maintenance Tightening the CablesRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Cable Diagrams Right ArmWeight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103AFor That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scaleX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key QtyExploded