Weider WESY59101 Welded, ADJUSTMENTS, beginning on page 21 of this manual, Maintenance on

Page 20

55.Lubricate a 1/2” x 4” Bolt (68). Attach the Foot Press Plate (29) to the Press Leg Lever (90) with the Bolt and a 1/2” Nylon Jamnut (36).

56.Press two 3/4” Round Inner Caps (43) into each of the two Pad Tubes (42).

Slide a Foam Pad (30) onto one side of a Pad Tube (42). Slide the Pad Tube through the hole in the Leg Lever (41). Slide another Foam Pad onto the other side of the Pad Tube.

Slide a Foam Pad (30) onto one side of the other Pad Tube (42). Insert the Pad Tube through the welded tube on the Butterfly Front Leg (3). Slide another Foam Pad onto the other side of the Pad Tube.

57.Attach the Curl Pad (91) to the Preacher Post (39) with four 1/4” x 3/4” Bolts (49).

Slide the Preacher Post (39) into the Butterfly Front Leg (3) and secure it by inserting the Large Adjustment Knob (46) and turning it clockwise until tight.

55

68

Lubricate

 

 

 

 

90

 

 

 

 

 

 

 

36

 

29

 

 

56

 

 

Welded

 

 

 

Tube

 

 

 

30

 

42

 

41

 

 

 

 

 

43

 

 

 

 

3

 

 

 

42

30

 

 

 

57

 

 

 

 

49

 

 

 

46

 

91

 

 

 

 

 

39

49

 

 

 

3

58. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in

ADJUSTMENTS, beginning on page 21 of this manual.

 

Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over

 

the pulleys. If one of the cables does not move smoothly, find and correct the problem.

IMPORTANT: If the

cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE

 

DIAGRAMS on page 25 and 26 of this manual for proper cable routing. If there is any slack in the

 

cables, you will need to remove the slack by tightening the cables. See TROUBLESHOOTING AND

 

MAINTENANCE on page 24.

 

20

Image 20
Contents QUESTIONS? Model No. WESY59101 Serial NoSerial Number Decal Under Seat Customer HOT LineTable of Contents Limited WarrantyImportant Precautions Replacement decal Apply the decal in the location shownMake sure all parts are properly tightened Ing down Decal shownUsing the weight system Before YOU BeginFor your benefit, read this manual carefully before DecalAssembly Cable AssemblyArm Assembly To open the parts bag for that stageFrame Assembly AssemblyDo not tighten the Nylon Locknuts yet Press the Weight Tube Bumper 18 into the Weight Tube See the inset drawingCorner bar of the Press Base SlotTighten the Nylon Locknuts used in steps ARM AssemblyLocknuts 50. Do not tighten the Nylon Locknuts yet Bolt and a 3/8 Nylon Locknut HandlesCable Assembly Able to pivot easilyInsert two 2 Square Inner Caps 28 into the Leg Lever 101Trap is turned to hold the Cable in place Hold the Cable in placeFrame 9. Attach a 3/8 Flat Washer 48 and a Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8Nylon Locknut Wrap the Ab Pulley 47 around another 3 1/2Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 PulleyWrap the Weight Cable 72 around a 3 1/2 Pulley Cable Trap is turned to hold the Cable in place4 Bolt 57 and a 3/8 Nylon Jamnut Cable in placeBe sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 BoltsDo not tighten the Nylon Locknut yet To hold the Cable in place Be surePlace Hold the Cable 75 in placeSeat Assembly Locate and open the parts bag labeled Seat AssemblyWelded ADJUSTMENTS, beginning on page 21 of this manualMaintenance on Adjustments Attaching the LAT BAR or AB Strap to High Pulley StationAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or NylonAttaching the AB Strap to the AB Pulley Station Adjusting the BackrestAdjusting the Curl PAD Weight Resistance Chart Retighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Troubleshooting and MaintenanceTightening the Cables Cable Diagrams Right ArmWeight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103AFor That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scaleX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key QtyExploded