Weider WESY59101 user manual See the inset drawing, Corner bar of the Press Base, Slot

Page 8


9.	See the inset drawing.		Insert two Weight Inserts
	(56) into each Weight (21).
	Set	the two Weight Bumpers (51) over the holes in
	the	corner bar of the Press Base (6).

Slide the Weight Guides (15) through the Weight Bumpers (51) and the holes in the Press Base (6). Secure the Weight Guides to the Press Base with

two 3/8” x 2 3/4” Bolts (89), four 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50).

Slide the Weights (21) onto the Weight Guides (15), stacking them on top of the Weight Bumpers (51).

Note: Be sure the Weights are oriented so that the slots in the Weights are toward the front, as shown.

10.Press the Weight Tube Bumper (18) into the Weight Tube (17).

Slide the Top Weight (16) onto the Weight Guides (15), so that the Weight Tube (17) goes into the center hole in the Weights (21).

11.Press a 1 1/2” x 2 1/2” Inner Cap (83) into the end of the Press Top Frame (9).

Attach the Press Top Frame (9) and a Support

Plate (94) to the Press Upright (2) with two 3/8” x 2 1/2” Bolts (87) and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts yet.

Note: Be sure that the Weight Guides (15) are properly positioned in relation to the Press Top Frame (9), as shown in drawing 12 on the next page.

8

9
56		15
		15
		21
21		Slot
		Slot
	89
		51	89
			89
48			48
			48
	48	48
6	48
6		50
		50
10
16
		15
17		18
		18
		21
11
87
94
9
		15
83		50
		50
50
		2

Image 8

Contents QUESTIONS? Model No. WESY59101 Serial NoSerial Number Decal Under Seat Customer HOT LineTable of Contents Limited WarrantyImportant Precautions Replacement decal Apply the decal in the location shownMake sure all parts are properly tightened Ing down Decal shownUsing the weight system Before YOU BeginFor your benefit, read this manual carefully before DecalAssembly Cable AssemblyArm Assembly To open the parts bag for that stageFrame Assembly AssemblyDo not tighten the Nylon Locknuts yet Press the Weight Tube Bumper 18 into the Weight Tube See the inset drawingCorner bar of the Press Base SlotTighten the Nylon Locknuts used in steps ARM AssemblyLocknuts 50. Do not tighten the Nylon Locknuts yet Bolt and a 3/8 Nylon Locknut HandlesCable Assembly Able to pivot easilyInsert two 2 Square Inner Caps 28 into the Leg Lever 101Trap is turned to hold the Cable in place Hold the Cable in placeFrame 9. Attach a 3/8 Flat Washer 48 and a Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8Nylon Locknut Wrap the Ab Pulley 47 around another 3 1/2Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 PulleyWrap the Weight Cable 72 around a 3 1/2 Pulley Cable Trap is turned to hold the Cable in place4 Bolt 57 and a 3/8 Nylon Jamnut Cable in placeBe sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 BoltsDo not tighten the Nylon Locknut yet To hold the Cable in place Be surePlace Hold the Cable 75 in placeSeat Assembly Locate and open the parts bag labeled Seat AssemblyWelded ADJUSTMENTS, beginning on page 21 of this manualMaintenance on Adjustments Attaching the LAT BAR or AB Strap to High Pulley StationAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or NylonAttaching the AB Strap to the AB Pulley Station Adjusting the BackrestAdjusting the Curl PAD Weight Resistance Chart Retighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Troubleshooting and MaintenanceTightening the Cables Cable Diagrams Right ArmWeight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103AFor That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scaleX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key QtyExploded