Weider WESY59101 user manual Frame 9. Attach a 3/8 Flat Washer 48 and a, Nylon Locknut

Page 13

27.Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Insert the Ab Cable down through the Press Top

Frame (9). Attach a 3/8” Flat Washer (48) and a

5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press Top Frame and the

3 1/2” Pulley. Secure another 5/8” x 3/4” Bushing and 3/8” Flat Washer to the Bolt with a 3/8” Nylon Locknut (50).

28.Remove the preassembled 3/8” x 2” Bolts (54) from the other Adjustable Pulley Plates (23).

Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley and a Cable Trap (25) between the top holes in the Adjustable Pulley

Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8”

Nylon Locknut (50). Be sure that the Cable Trap is turned to hold the Cable in place.

29.Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Attach the 3 1/2” Pulley to the rear bracket on the Press Top Frame (9) with a 3/8” x 2” Bolt (54) and a

3/8” Nylon Locknut (50).	Be sure the Ab Cable is
routed in the direction shown.

Wrap the Ab Pulley (47) around another 3 1/2”

Pulley (24). Attach the 3 1/2” Pulley to the forward bracket on the Press Top Frame (9) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).

30.Wrap the Ab Cable (47) around a 3 1/2” Pulley (24) and slide the Ab Cable through the hole in the

Press Upright (2). Attach a 3/8” Flat Washer (48)

and a 5/8” x 3/4” Bushing (66) to a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press Upright and

the 3 1/2” Pulley. Secure another 5/8” x 3/4” Bushing and 3/8” Flat Washer to the Bolt with a 3/8” Nylon Locknut (50).

13

27			66
			66
62	24
62			48
			48
	48		50
	48
47
		9
28
	47
		25
54
			24
		23	50
			50
29	Bracket
9
		54	24
			24
54			82
	24		50
	24
	47
30
			66
	2		24
	2
62			66
62
48
		48
			50
47

Image 13

Contents Model No. WESY59101 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT LineLimited Warranty Table of ContentsReplacement decal Apply the decal in the location shown Important PrecautionsMake sure all parts are properly tightened Ing down Decal shownBefore YOU Begin Using the weight systemFor your benefit, read this manual carefully before DecalCable Assembly AssemblyArm Assembly To open the parts bag for that stageAssembly Frame AssemblyDo not tighten the Nylon Locknuts yet See the inset drawing Press the Weight Tube Bumper 18 into the Weight TubeCorner bar of the Press Base SlotLocknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon LocknutAble to pivot easily Cable AssemblyInsert two 2 Square Inner Caps 28 into the Leg Lever 101Hold the Cable in place Trap is turned to hold the Cable in placePlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Frame 9. Attach a 3/8 Flat Washer 48 and aNylon Locknut Wrap the Ab Pulley 47 around another 3 1/2Be sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on itCable Trap is turned to hold the Cable in place Wrap the Weight Cable 72 around a 3 1/2 Pulley4 Bolt 57 and a 3/8 Nylon Jamnut Cable in placeRemove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in placeDo not tighten the Nylon Locknut yet Be sure To hold the Cable in placePlace Hold the Cable 75 in placeLocate and open the parts bag labeled Seat Assembly Seat AssemblyMaintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Attaching the LAT BAR or AB Strap to High Pulley Station AdjustmentsAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or NylonAdjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable DiagramsWeight Cable Cable ID Stack Page Part No R0103A Ordering Replacement PartsFor That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103AX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty KeyExploded