Weider WESY59101 user manual Locate and open the parts bag labeled Seat Assembly

Page 19

SEAT ASSEMBLY

51.Locate and open the parts bag labeled “SEAT ASSEMBLY.”

Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49).

Repeat this step with the other Seat (not shown) and the Press Seat Frame (not shown).

52.Press a 1 1/2” Square Inner Cap (35) into the end of the Press Backrest Frame (44). Attach a Backrest (12) to the Press Backrest Frame with four 1/4” x 3/4” Bolts (49).

Pull out the Adjustment Knob (5) on the Press Upright (2) as far as it can go. Slide the Press Backrest Frame (44) into the Press Upright and snap the Adjustment Knob into a hole in the Press Backrest Frame. Turn the Adjustment Knob clock- wise until tight.

53.Press a 1 1/2” Square Inner Cap (35) into the end of the Butterfly Backrest Frame (70). Attach the other Backrest (12) to the Butterfly Backrest Frame with four 1/4” x 3/4” Bolts (49).

Pull out the Adjustment Knob (5) on the Butterfly Upright (1) as far as it can go. Slide the Butterfly Backrest Frame (70) into the Butterfly Upright and snap the Adjustment Knob into a hole in the Butterfly Backrest Frame. Turn the Adjustment Knob clockwise until tight.

54.See drawing A. Attach the Shroud (34) to the Press Top Frame (9) with two #8 x 1/2” Screws (45).

See drawing B. Attach the Shroud (34) to the Press Base (6) with two #8 x 1/2” Screws (45).

19

51	14
	14		13
			13
		49
52
		49	2
		44
			5
			35
	12	49
		49
53	35	49
	35	49
	5	70	12
	5	70
	1	49
54		A	B
		9
	45
	34
		34
			6
			45

Image 19

Contents Customer HOT Line QUESTIONS?Model No. WESY59101 Serial No Serial Number Decal Under SeatLimited Warranty Table of ContentsIng down Decal shown Important PrecautionsReplacement decal Apply the decal in the location shown Make sure all parts are properly tightenedDecal Using the weight systemBefore YOU Begin For your benefit, read this manual carefully beforeTo open the parts bag for that stage AssemblyCable Assembly Arm AssemblyAssembly Frame AssemblyDo not tighten the Nylon Locknuts yet Slot Press the Weight Tube Bumper 18 into the Weight TubeSee the inset drawing Corner bar of the Press BaseLocknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon Locknut101 Cable AssemblyAble to pivot easily Insert two 2 Square Inner Caps 28 into the Leg LeverHold the Cable in place Trap is turned to hold the Cable in placeWrap the Ab Pulley 47 around another 3 1/2 Frame 9. Attach a 3/8 Flat Washer 48 and aPlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Nylon LocknutBe sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on itCable in place Wrap the Weight Cable 72 around a 3 1/2 PulleyCable Trap is turned to hold the Cable in place 4 Bolt 57 and a 3/8 Nylon JamnutRemove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in placeDo not tighten the Nylon Locknut yet Hold the Cable 75 in place To hold the Cable in placeBe sure PlaceLocate and open the parts bag labeled Seat Assembly Seat AssemblyMaintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Attaching the LAT BAR, AB STRAP, or Nylon AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Ab Strap 81 can be attached in the same mannerAdjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable DiagramsWeight Cable Cable ID Stack Page Part No R0103A Ordering Replacement PartsFor That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103AX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty KeyExploded