Weider WESY59101 user manual Cable Diagrams, Right Arm

Page 25

CABLE DIAGRAMS

The cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the Ab Cable (47), the Butterfly Cable (73), and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly. The starting and ending points of each Cable have been labeled. The numbers

show the proper route for each Cable.IMPORTANT: If the Cables have not been correctly routed, the weight system will not function properly and damage may occur.

Leg Press Cable (75)

6

9

10

11—Press Upright

75

3

	2
8	1—Press Upright
	1—Press Upright

4
Ab Cable (47)	Butterfly Cable (73)
	2
	4
4	5—Left Arm
5
1—High Pulley
	2
	1—Right Arm
	3
6—Ab Pulley	3
	3

25

Image 25

Contents Model No. WESY59101 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT LineLimited Warranty Table of ContentsReplacement decal Apply the decal in the location shown Important PrecautionsMake sure all parts are properly tightened Ing down Decal shownBefore YOU Begin Using the weight systemFor your benefit, read this manual carefully before DecalCable Assembly AssemblyArm Assembly To open the parts bag for that stageAssembly Frame AssemblyDo not tighten the Nylon Locknuts yet See the inset drawing Press the Weight Tube Bumper 18 into the Weight TubeCorner bar of the Press Base SlotLocknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon LocknutAble to pivot easily Cable AssemblyInsert two 2 Square Inner Caps 28 into the Leg Lever 101Hold the Cable in place Trap is turned to hold the Cable in placePlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Frame 9. Attach a 3/8 Flat Washer 48 and aNylon Locknut Wrap the Ab Pulley 47 around another 3 1/2Be sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on itCable Trap is turned to hold the Cable in place Wrap the Weight Cable 72 around a 3 1/2 Pulley4 Bolt 57 and a 3/8 Nylon Jamnut Cable in placeRemove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in placeDo not tighten the Nylon Locknut yet Be sure To hold the Cable in placePlace Hold the Cable 75 in placeLocate and open the parts bag labeled Seat Assembly Seat AssemblyMaintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Attaching the LAT BAR or AB Strap to High Pulley Station AdjustmentsAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or NylonAdjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable DiagramsWeight Cable Cable ID Stack Page Part No R0103A Ordering Replacement PartsFor That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103AX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty KeyExploded