Weider WESY59101 user manual Important Precautions, Make sure all parts are properly tightened

Page 3

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system.

1.Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in the literature.

2.It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.

3.The weight system is intended for home use only. Do not use the weight system in any commercial, rental, or institutional setting.

4.Use the weight system only on a level sur- face. Cover the floor beneath the weight sys- tem to protect the floor.

5.Make sure all parts are properly tightened

each time you use the weight system. Replace any worn parts immediately.

6.Keep children under 12 and pets away from the weight system at all times.

7.Keep hands and feet away from moving parts.

8.Always wear athletic shoes for foot protec- tion.

9.Never release the press arm, butterfly arms, leg lever, leg press, lat bar, ab strap, or nylon strap while weights are raised. The weights will fall with great force.

10.The weight system is designed to support a a maximum user weight of 300 pounds.

11.Make sure that the cables remain on the pul- leys at all times. If the cables bind while you are exercising, stop immediately and make

sure that the cables are on all of the pulleys.

12.Always disconnect the lat bar from the

weight system when performing an exercise

that does not use the lat bar

.

 

 

 

13.If you feel pain or dizziness at any time while exercising, stop immediately and begin cool-

ing down.

14.The decal shown

here has been placed on the weight

system in the loca- tion shown on page 4. If the decal is

missing or illegible, please call our Customer Service Department toll-free

at 1-800-999-3756, Monday through Friday, 6 a.m. until 6

p.m. Mountain Time, to order a free

replacement decal.

Apply the decal in the location shown.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Customer HOT Line QUESTIONS?Model No. WESY59101 Serial No Serial Number Decal Under SeatLimited Warranty Table of ContentsIng down Decal shown Important PrecautionsReplacement decal Apply the decal in the location shown Make sure all parts are properly tightenedDecal Using the weight systemBefore YOU Begin For your benefit, read this manual carefully beforeTo open the parts bag for that stage AssemblyCable Assembly Arm AssemblyAssembly Frame AssemblyDo not tighten the Nylon Locknuts yet Slot Press the Weight Tube Bumper 18 into the Weight TubeSee the inset drawing Corner bar of the Press BaseARM Assembly Locknuts 50. Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts used in steps Handles Bolt and a 3/8 Nylon Locknut101 Cable AssemblyAble to pivot easily Insert two 2 Square Inner Caps 28 into the Leg LeverHold the Cable in place Trap is turned to hold the Cable in placeWrap the Ab Pulley 47 around another 3 1/2 Frame 9. Attach a 3/8 Flat Washer 48 and aPlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Nylon LocknutBe sure Weight Cable is in the groove of the 3 1/2 Pulley Weight Cable has a bolt, and the other End has a ball on itCable in place Wrap the Weight Cable 72 around a 3 1/2 PulleyCable Trap is turned to hold the Cable in place 4 Bolt 57 and a 3/8 Nylon JamnutRemove the preassembled 3/8 x 1 3/4 Bolts Be sure that Cable Trap is turned to hold the Cable in placeDo not tighten the Nylon Locknut yet Hold the Cable 75 in place To hold the Cable in placeBe sure PlaceLocate and open the parts bag labeled Seat Assembly Seat AssemblyADJUSTMENTS, beginning on page 21 of this manual Maintenance onWelded Attaching the LAT BAR, AB STRAP, or Nylon AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Ab Strap 81 can be attached in the same mannerAdjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Troubleshooting and Maintenance Tightening the CablesRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Right Arm Cable DiagramsWeight Cable Cable ID Stack Page Part No R0103A Ordering Replacement PartsFor That Assembly Stage Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale R0103AX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty KeyExploded
Top Page Image Contents