Weider WESY59101 user manual Be sure that Cable Trap is turned to hold the Cable in place

Page 16

39. Wrap the Weight Cable (72) around a 3 1/2” Pulley			39		47
	(24). Attach the 3 1/2” Pulley and a Cable Trap (25)		39


	between the lowest holes in the Adjustable Pulley				23
	Plates (23) hanging from the Ab Cable (47) with a			54	23
	Plates (23) hanging from the Ab Cable (47) with a			54
	3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50)			25	50
	that was removed in step 28.	Be sure that the		25


	Cable Trap is turned to hold the Cable in place.
				24
					72
40.	Remove the preassembled 3/8” x 1 3/4” Bolts (57)		40
	from the Small Pulley Plates (22).		40
	from the Small Pulley Plates (22).
	Wrap the Weight Cable (72) around a 3 1/2” Pulley
	(24). Attach the 3 1/2” Pulley between two Small				72
	Pulley Plates (22) with a 3/8” x 1 3/4” Bolt (57) and			24	72
	a 3/8” Nylon Locknut (50).			24
	a 3/8” Nylon Locknut (50).
			50		57
					22
41. Wrap the Weight Cable (72) around a 4 1/2” Pulley			41
	(82). Attach the 4 1/2” Pulley to the bracket on the		41
	(82). Attach the 4 1/2” Pulley to the bracket on the
	Press Top Frame (9) with a 3/8” x 2” Bolt (54) and a
	3/8” Nylon Locknut (50).		54		72
			54
				82	50
				82
					Bracket
				9
42. Place a 1/2” Flat Washer (11) on top of the Weight			42
	Tube (17).		42
	Tube (17).
	Thread a 1/2” Plain Nut (100) halfway onto the bolt			72
	on the Weight Cable (72). Screw the bolt on the			72
	on the Weight Cable (72). Screw the bolt on the
	Weight Cable into the Weight Tube (17) a couple of			100
	turns.			11
				11
	Tighten the 1/2” Plain Nut (100) down onto the 1/2”			17
	Flat Washer (11).			17
	Flat Washer (11).

16

Image 16

Contents QUESTIONS? Model No. WESY59101 Serial NoSerial Number Decal Under Seat Customer HOT LineTable of Contents Limited WarrantyImportant Precautions Replacement decal Apply the decal in the location shownMake sure all parts are properly tightened Ing down Decal shownUsing the weight system Before YOU BeginFor your benefit, read this manual carefully before DecalAssembly Cable AssemblyArm Assembly To open the parts bag for that stageFrame Assembly AssemblyDo not tighten the Nylon Locknuts yet Press the Weight Tube Bumper 18 into the Weight Tube See the inset drawingCorner bar of the Press Base SlotLocknuts 50. Do not tighten the Nylon Locknuts yet ARM AssemblyTighten the Nylon Locknuts used in steps Bolt and a 3/8 Nylon Locknut HandlesCable Assembly Able to pivot easilyInsert two 2 Square Inner Caps 28 into the Leg Lever 101Trap is turned to hold the Cable in place Hold the Cable in placeFrame 9. Attach a 3/8 Flat Washer 48 and a Plates 23 with a 3/8 x 2 Bolt 54 and a 3/8Nylon Locknut Wrap the Ab Pulley 47 around another 3 1/2Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 PulleyWrap the Weight Cable 72 around a 3 1/2 Pulley Cable Trap is turned to hold the Cable in place4 Bolt 57 and a 3/8 Nylon Jamnut Cable in placeBe sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 BoltsDo not tighten the Nylon Locknut yet To hold the Cable in place Be surePlace Hold the Cable 75 in placeSeat Assembly Locate and open the parts bag labeled Seat AssemblyMaintenance on ADJUSTMENTS, beginning on page 21 of this manualWelded Adjustments Attaching the LAT BAR or AB Strap to High Pulley StationAb Strap 81 can be attached in the same manner Attaching the LAT BAR, AB STRAP, or NylonAdjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Tightening the Cables Troubleshooting and MaintenanceRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Cable Diagrams Right ArmWeight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103AFor That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scaleX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key QtyExploded