Weider WESY59101 user manual R0103A, Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scale

Page 30

PART IDENTIFICATION CHART—Model No. WESY59101

R0103A

Cable Clip (69)

1/2" Flat Washer (11)

1/2" Plain Nut (100)

3/8" Nylon Locknut (50)

5/16" Nylon Locknut (64)

1/2" x 3/4" Spacer (97)

5/8” x 3/4” Bushing (66)

3/8" Flat Washer (48)

1/2" Nylon Jamnut (36)

3/8" Nylon Jamnut (63)

5/16" Nylon Jamnut (101)

5/8" x 1/2" Spacer (99)

4 1/2" Pulley (82) (Not shown to scale)

"V" Pulley (27) (Not shown to scale)

3 1/2" Pulley (24) (Not shown to scale)

Retainer Ring (31)

3/4" Round Inner Cap (43)	1" Round Inner Cap (86)	1" Round Outer Cap (38)

Image 30

Contents Serial Number Decal Under Seat QUESTIONS?Model No. WESY59101 Serial No Customer HOT LineTable of Contents Limited WarrantyMake sure all parts are properly tightened Important PrecautionsReplacement decal Apply the decal in the location shown Ing down Decal shownFor your benefit, read this manual carefully before Using the weight systemBefore YOU Begin DecalArm Assembly AssemblyCable Assembly To open the parts bag for that stageFrame Assembly AssemblyDo not tighten the Nylon Locknuts yet Corner bar of the Press Base Press the Weight Tube Bumper 18 into the Weight TubeSee the inset drawing SlotARM Assembly Locknuts 50. Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts used in steps Bolt and a 3/8 Nylon Locknut HandlesInsert two 2 Square Inner Caps 28 into the Leg Lever Cable AssemblyAble to pivot easily 101Trap is turned to hold the Cable in place Hold the Cable in placeNylon Locknut Frame 9. Attach a 3/8 Flat Washer 48 and aPlates 23 with a 3/8 x 2 Bolt 54 and a 3/8 Wrap the Ab Pulley 47 around another 3 1/2Weight Cable has a bolt, and the other End has a ball on it Be sure Weight Cable is in the groove of the 3 1/2 Pulley4 Bolt 57 and a 3/8 Nylon Jamnut Wrap the Weight Cable 72 around a 3 1/2 PulleyCable Trap is turned to hold the Cable in place Cable in placeBe sure that Cable Trap is turned to hold the Cable in place Remove the preassembled 3/8 x 1 3/4 BoltsDo not tighten the Nylon Locknut yet Place To hold the Cable in placeBe sure Hold the Cable 75 in placeSeat Assembly Locate and open the parts bag labeled Seat AssemblyADJUSTMENTS, beginning on page 21 of this manual Maintenance onWelded Ab Strap 81 can be attached in the same manner AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Attaching the LAT BAR, AB STRAP, or NylonAdjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart Troubleshooting and Maintenance Tightening the CablesRetighten the 1/2 Plain Nut down onto the 1/2 Flat Washer Cable Diagrams Right ArmWeight Cable Cable ID Stack Page Ordering Replacement Parts Part No R0103AFor That Assembly Stage R0103A Pulley 27 Not shown to scale 2 Pulley 24 Not shown to scaleX 3 1/4 Bolt 2 Square Inner Cap 3 Inner Cap 2 x 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key QtyExploded