Whirlpool Gas Washer/Dryer ConnectVent, CompleteInstallation, Electrical Shock Hazard

Page 12
ConnectVent

4.Attach the flexible gas connector to the ½" NPT adapter. Do not use pipe-joint compound for this connection.

There should be a natural loop in the flexible gas connector. The flexible gas connector must not be twisted, kinked, or attached with any sharp bends.

5.All connections must be wrench tightened.

6.Open the shutoff valve in the supply. The valve is open when the handle is parallel to the gas pipe.

A

B

A. Closed valve

B. Open valve

7.Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found.

ConnectVent

1.Using a 4" (102 mm) clamp, connect vent to exhaust outlet in washer/dryer. If connecting to existing vent, make sure the vent is clean. The vent must fit over the exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (102 mm) clamp.

2.Move washer/dryer into its final location. Do not crush or kink vent. Make sure washer/dryer is level.

3.Check that there are no kinks in the flexible gas line.

CompleteInstallation

1.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2.Check that you have all of your tools.

3.Dispose of/recycle all packaging materials. Keep the plastic foam for use if the washer/dryer should be transported.

4.Check the washer/dryer’s final location. Be sure the vent is not crushed or kinked.

5.Check that the washer/dryer is level and front leveling feet are tight. See “Level Washer/Dryer.”

CompleteInstallationWARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

6.Plug into a grounded 3 prong outlet. Turn on power.

7.Check that the water faucets are on.

8.Check for leaks around faucets and inlet hoses.

9.Remove the blue protective film on the console and any tape remaining on the washer/dryer.

10.Read the Washer/Dryer User Instructions.

11.Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

12.To test the washer, measure 12 the normal recommended amount of detergent and pour it into the washer. Close the lid. Select HEAVY DUTY and pull out the Cycle Control knob. Allow the washer to complete one whole cycle.

13.To test the dryer, set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

Washer/dryer is plugged into a grounded 3 prong outlet. Start button has been firmly pushed.

Electrical supply is connected.

Household fuses are intact and tight, or circuit breakers have not tripped.

Dryer door is closed.

14.When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you do not feel heat, turn off the dryer and check to see whether the gas supply line shutoff valve is open.

If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as outlined above.

If the gas supply line shutoff valve is open, contact a qualified technician.

12

Image 12
Contents WASHER/DRYER SAFETY DANGER WARNING2769CMGASWASHER/DRYER INSTALLATIONINSTRUCTIONS INSTRUCTIONSD’INSTALLATION LAVEUSE/SÉCHEUSEÀGAZ DE2769CMWHAT TO DO IF YOU SMELL GAS Do not try to light any appliance ToolsandParts AlternatePartsLocationRequirements INSTALLATIONINSTRUCTIONSDrainSystem Installation ClearancesWasher/Dryer Dimensions Installation spacing for recessed area or closet installationElectricalRequirementsGasSupplyRequirements GROUNDING INSTRUCTIONSSAVE THESE INSTRUCTIONS Laundry tub drain system view CVentingRequirements Gas supply pressure testingIf using an existing vent system Vent materialRemoveShippingStrap Excessive Weight HazardUse two or more people to move and install washer/dryer Rigid metal ventInstallLevelingLegs ConnecttheDrainHoseConnecttheInletHoses Install the front leveling feetSecuretheDrainHose Clear the water linesConnect the inlet hoses to the washer If you are working in a closet or recessed areaPlanVentSystem Recommended exhaust installationsOptional exhaust installations Alternate installations for close clearancesInstallVentSystem LevelWasher/DryerMakeGasConnection Vent system chartCompleteInstallation ConnectVentIf the dryer will not start, check the following SÉCURITÉDELALAVEUSE/SÉCHEUSE DANGER AVERTISSEMENTQUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ INSTRUCTIONSD’INSTALLATION Exigencesd’emplacementAVERTISSEMENT OutillageetpiècesEspacements d’installation Installation dans une maison mobile - autres exigencesDimensions de la laveuse/sécheuse Systèmedevidange SpécificationsélectriquesSystème de vidange avec évier de buanderie illustration C Système de vidange par le plancher illustration DSpécificationsdel’alimentationengaz Type de gaz Gaz naturelConversion au gaz de pétrole liquéfié Un technicien qualifié doit effectuer la conversionExigencesconcernantl’évacuation Matériel pour l’évacuationRisque d’incendie Utiliser un conduit d’évacuation en métal lourd Ne pas utiliser un conduit d’évacuation en plastiqueInstallationdespiedsdenivellement Enleverlasangled’expéditionRaccordementdutuyaudevidange Installation des pieds de nivellement avantRaccordementdestuyauxd’alimentation Pour utilisation avec vidange par le plancherConnecter les tuyaux d’alimentation aux robinets d’eau Nettoyer les conduites d’eauImmobilisationdutuyaudevidange Planificationdusystèmed’évacuationInstallations d’évacuation recommandées Installations d’évacuation facultativesAutres installations où le dégagement est réduit Dispositions spéciales pour les installations dans une maison mobileTableau des systèmes d’évacuation Déterminer l’itinéraire d’acheminement du conduitInstallationdusystèmed’évacuation Nivellementdelalaveuse/sécheuseRaccordementàlacanalisationdegaz Acheverl’installation Raccordement du conduitd’évacuationSi la sécheuse ne démarre pas, vérifier ce qui suit Page Page W10222381A 2008Benton Harbor, Michigan 10/08