Miele W 1930I operating instructions Plumbing, Connection to the drain sys- tem

Page 40

Plumbing

Connect the cold water supply hose (hose marked blue) to the cold water valve and the hot water supply hose (hose marked red) to the hot water valve.

Turn on the valves and check for leaks. The water pressure must be within 15-145 psi (1-10 bar). If the water pressure is greater than 145 psi

(10 bar), a pressure reducer must be in- stalled. If the water pressure is below

15 psi (1 bar), insufficient water may be available for a complete fill.

The water supply hoses are equipped with filters; please do not remove these filters.

Special note

If connecting the machine to a cold water supply only, use the included Y- adapter to connect both hoses to the cold water valve, otherwise the cor- rect functioning of the machine could be impaired. The machine should not be connected to hot water only.

Connection to the drain sys- tem

The 5 ft. (1.5 m) drain hose may be con- nected as follows:

1.Directly into a sink: hook the hose over the edge of the sink and secure it firmly (e.g. by tying the hose to the water faucet).

2.Connection to a stand pipe: place the drain hose into a 1 1/2" (38 mm) stand pipe and firmly secure it. (An anti-siphoning device is not required as there is one built into the ma- chine.)

3.To a floor drain: if desired, the drain hose may be extended to 15 ft. (4.5 m) maximum.

The machine drains using a pump with a maximum delivery height of 4 ft.

(1.2 m).

Make sure there are no kinks in the drain hose.

The machine is equipped with an air- gap/anti-siphoning system so that no minimum drain height is required.

40

Image 40
Contents For the W 1930i Washing Machine Contents Guide to the machine Detergent dispenser drawer Important safety instructions Disposal of the packing material Disposal of your old machineEconomical usage EconomyBefore washing Preparing the LaundryPrepare the wash load To start a program Press the Door button to open the door Load the machineRecommended load sizes are noted below Close the machine doorAfter washing End of ProgramClose the drum door To cancel a program Changing the program sequenceTo interrupt a program To change an incorrectly selected programAdding detergent Adding fabric softener or starch Using the Starch program to dis- pense liquid starchStarch Program selection 11 lbs Program sequence ExplanationsInterim rinse Graduated rinseStarch Spin Fine rinse Graduated spinFinal spin WoolensTextile care symbols Temperature Conversion ChartWashing C Tumble dryAdditional options Pre-washWater plus Gentle washDelay start/Time remaining indicator Delay StartTime display Hmin Remaining timeCleaning the washing machine User Maintenance Instructions Cleaning and careCleaning the detergent drawer Cleaning and care Cleaning the drain pump and lint trapCleaning and Care To clean the filter in the inlet hose Cleaning the water inlet filtersTo clean the filter in the inlet valve Problem solving guide Program does notStart? Check p / q indiWhat to do if Cause Remedy Into the machine? Large residues of deter Drawer?There is an excessive Build-up of foam?Grey greasy particles Cling to washed laundry?Give the required result? After washing pilling apOpening the drum door in the event of a power failure To check water pressure Electric socketAfter sales service Installation Instructions Installation Installation surfaceInstallation Removing the shipping strutsInstallation Levelling the machine BuildingMatching the control panel to the adjacent washer fronts Please note the followingInstalling the front panel Plate locations 1 and 2 onlyInstallation Sizing the toekick Installing the toekick Washer-Dryer stackWater hardness reminder Plumbing Connection to the drain sys- temElectrical connection Grounding InstructionsOperating Instructions Programmable functions High water level only in Cottons rinses5th Rinse in the Cottons program No water intake through compartmentProgrammable functions StepDProgram Lock Child safety feature Desired function AHigh water level B5th rinse cycleAdditional rinse in Rapid wash Deleting the additional func- tions To check if the function has been storedCarry out Steps 1 to Installation Instructions Technical data DimensionsTechnical data Page Page