Fisher & Paykel 517735 service manual Option Adjustment Mode, Wash Water Temperature All Phases

Page 32

7.0 OPTION ADJUSTMENT MODE

Smartdrive can be adjusted to operate under a number of different conditions OPTION ADJUSTMENT MODE may be used to customise Smartdrive. Some of this information is available to the user in the ‘Use and Care Manual’. For IW see Appendix E. The features that can be adjusted in this mode are:-

a)Water Temperature

b)Rinse Options

c)Number of End of Cycle Warning Beeps GW (only)

d)Auto out of Balance Recovery – GW and MW (only)

e)Auto Water Level Adjustment - GW (only)

f)Water saver Rinse Volume Adjustment - GW (only)

NB. Phase 1-3. Entering Option Adjustment mode sets the size of Smartdrive into EEPROM

To Select the OPTION ADJUSTMENT MODE

1.With Smartdrive powered on at the wall and with the LEDs off, press and hold the START / PAUSE button. Then press the POWER button. Two quick beeps will sound and the LEDs on the front panel will change. The controls and LEDs on the front panel will now serve different functions from the normal wash functions.

2.Smartdrive can now be adjusted to suit the owners preference.

3.To return Smartdrive to Normal operation, press the POWER button.

7.1Wash Water Temperature – All Phases

It is possible to adjust the water temperature of each of the wash temperature settings, i.e. Cold, Cold/Warm, Warm, Warm/Hot, Hot. Phase 5 MW can only adjust warm. Phase 5 LW & AW are not adjustable.

•Do not use the household water taps or water heater controls to vary the wash temperature. The automatic water temperature control system fitted will compensate for variations in household water temperature and pressure. Adjusting the water pressure or water flow with the household taps, or adjusting the water heater temperature, WILL NOT alter the wash temperature. The method described below is the only method by which the water temperature can be altered.

•If Smartdrive is used in an installation where only a cold water supply is available, then the cold temperature range must be selected and the "cold water only" setting must be chosen in the option adjustment mode. If the temperature is set at any other level, Smartdrive will expect hot water when filling Smartdrive. As it will not detect any hot water, it will eventually display USER WARNING that there is no hot water, but it will not pause.

•It is recommend that the hot water temperature setting on the household water heater does not exceed 65oC, for personal safety and product reliability. This is especially important for Phase 5 MW, LW & AW where the ‘Hot’ setting corresponds to hot water only.

- 27 -

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Phase 1 to 5 Smart Drive Electronic Washing MachinePhase 3 GW Phase 4 GWPhase 5 IW Phase 5 IwecoWhat PHASE, Size & Model is Your SMARTDRIVE? MW, GWTable of Contents Recycle Introduction HOW to Service SmartdriveIf Smartdrive has no Power see Section Smartdrive Servicing Quick Reference Guide Specifications ALL Terminals and Internal Parts should be Treated AS LiveInstallation InstallationRemoving Transit Restraint Inlet HosesInstallation Environment Water Supply Temperatures SafetyAccessories and Spare Parts Levelling SmartdriveSmartdrive Components Electronics Systems Phase Wiring Diagram Specifications MotorMotor Controller Module Water Level Measurement Pressure SensorDisplay Module Water Valves Installation Rotor Position SensorPump Motor Specifications PumpDiagram showing the Floating Bowl Inner and Outer BowlsDetection Of Inner Bowl Float Off Point Bowl Check Lid Switch and Out of Balance Switch Lid SwitchWater Temperature Sensing Smartdrive Information Favourite cycle GW only All PhasesCustomising Wash Cycles GW only Phase 3 to 5 only Water Saver GW only Phase 3 to 5 only Delay Start GW only Phase 2 to 5 onlyAuto Water Level GW only Phase 3 to 5 only Fabric Softener Dispenser All Phases Amount of Water Used in the Water Saver RinseWash Performance Information All Phases CreasingIf Smartdrive Powers Off mid cycle Smartdrive ProblemsIf Smartdrive Appears To Have No Power Noisy FloodingLeaking Continuous Spinning or Slow Spinning Poor Wash PerformanceSiphoning Radio Frequency Interference RFIEarth Leakage It Appears Smartdrive is doing nothingOption Adjustment Mode Wash Water Temperature All PhasesRinse Options All Phases Method of Setting the Wash TemperatureEnd of Cycle Warning Beeps GW Only All Phases PhaseAuto Water Fill Level Adjustment GW only Phase Out Of Balance Recovery Adjustment GW and MW only PhaseDiagnostic Mode What WAS the Last FAULT?Test LID, OUT of BALANCE, & Size Switches To Test Pump & Water ValvesRestart RecycleLOW Water Level LED OFF = Restart OFF Medium Water Level LED on = RE-CYCLE onPage Size Setting Mode Phase 4 and 5 only Insufficient Cold Water Cold Water LED flashing User WarningsInsufficient Hot Water Hot Water LED flashing No Water Both Hot and Cold Water LEDs flashing Overloaded Product High Water LED flashingRestart and Recycle Wash Progress LEDs flashing Phase 4Phase 1 to Demonstration Mode All LEDs flashing in patterns Fault Codes GWC08 GWM08 GWL08 THC08 THM08 THL08GWC09 GWM09 GWL09 IWM09 IWL09Smartdrive Phases 1 to 5 Fault Descriptions Phase 1 to 5 Motor Controller FaultPhase 1 Communications Fault Primary Source Motor ControllerPhase 1 to 5 Display Module Fault Phase 1 to 5 Size ErrorPrimary Source Display Module Action Primary Source Display ModulePhase 4 to Phase 1 to 5 Thermistor ErrorAction Phase Phase 2 toPhase 1 to 5 Pressure Sensor Fault Phase 1 to 5 Flood Protection ErrorPhase 1 Pump Fault Primary Source Pressure TubePhase 1 Pump Connection Fault Phase 5 IW LCD Initialisation Error28 30 xx Phase 1 Display / Motor Controller out of Sequence Primary Source Pump ActionPhase 1 MC Reset Error Phase 1 Pump Circuit ErrorPhase 1 Brake Resistor Fault Phase 1 to 5 Water Leak Fault Phase 1 to 5 Pump Block ErrorPrimary Source Pump System Secondary Source Mechanical ActionPhase 1 to 5 Tap or Pressure Sensor Tube Fault Phase 1 to 5 Bowl Dis-Engaged FaultPrimary Source Mechanical Primary Source SudsPhase 1 to 5 Temperature Sensor Fault Phase 1 Rotor Fault Primary SourcePhase 1 to 5 OOB Switch Fault Primary Source Mechanical ActionPhase 2 to 5 Water in Bowl During Spin Phase 5 Display FaultPrimary Source Pump System Action Secondary Source Motor ControllerPhase 2 to 3 Bowl Dis-engaged Fault Phase 2 to 5 Hot and Cold Valve FaultPrimary Source Wiring Phase 2 to 5 Cold Valve FaultPhase 2 to 5 Hot Valve Fault Phase 5 ECO Recirculation FaultPhase 5 ECO Recirculation Fault See fault code Secondary Source Diverter ValveSecondary Source Motor Phase 2 to 5 Rotor Position Sensor FaultPhase 2 to 5 Motor / Motor Control Step Fail Phase 4 to 5 Bowl Check Fault Phase 4 to 5 Motor Controller FaultPhase 4 Motor Controller Fault Primary Source- PumpPhase 2 to 3 Display / Motor Controller Comms. Error Phase 5 Machine Setup ErrorPhase 1 to 5 Single Rotor Position Sensor Error Primary Source Wiring ActionPhase 1 to 5 Repetitive Rotor Position Sensor Error Phase 1 to 4 Single Current TripPhase 1 to 4 Repetitive Current Trip Phase 4 Single Current Trip & Rotor Position Sensor ErrorPhase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Phase 5 Topdeck Showing Wiring Connections Mechanical Service SectionComplete Disassembly Phase 2 Topdeck Showing Wiring Connections NB DON’T Remove the Earth Connection from the WrapperPage Page Assembly Guidelines Motor Assembly & Disassembly AssemblyPump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Appendix a Binary Decoding Chart 8 Bits Wash Progress LEDsImportant Note Size SettingFault Finding / Fault Codes Pump Hood Kit Part Number 479188P WM013 Pump Hood KIT January 2000 Phases 2 toWiring Connections WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only Kit Lever Out of Balance & Bracket Phase 2 Part Number WM65 BIB Deflector April 1994- Phase 1 onlyWM70 Premature OUT of Balance February 1995 Phase 2 only WM80 Condensation KIT May 1996 Phase 2 & 3 only WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 toAppendix C Smarttool Appendix D Tools for Servicing Smartdrive Specifications for IW IW Quick Reference GuideModels Size Width Wash Load Capacity Compact Medium LargeIntroduction to IW Wash 1 Detergent Activating Wash Front loader type washWater Temperature Sensing Option Adjustment Mode for IW PumpOther Options Diagnostic Mode for IW Status DisplayFault Status Size Setting Mode for IW Recycle
Top Page Image Contents