Fisher & Paykel 517735 service manual Size Setting Mode Phase 4 and 5 only

Page 40

9.0 SIZE SETTING MODE – Phase 4 and 5 only

Phase 1-3sizes are determined by 2 switches on the display and protrusions on the console. When replacing Display or Motor Controller enter Option Adjustment mode to set these sizes in EEPROM. To check the size setting on Phase 1-3 use DIAGNOSTIC mode. See section 8.2. Size setting mode is required for Phase 1 spare (426518 Motor Controller and 426433 Display). For IW see service manual Appendix E..

It is important to set the size switch setting into the Motor Controller’s memory whenever a replacement Motor Controller or Display Module is fitted to Smartdrive. Failure to do this will result in Smartdrive faulting with fault code 9.

Accessing size setting mode is the best way to check the size for Phase 4 & 5 and Phase 1 spare. The size setting of Smartdrive may be checked in Diagnostic mode for all phases.

To set the size switch turn the power on at the power point and off at the console. Press and hold the TEMPERATURE UP button then press the POWER button. Smartdrive will give 4 short beeps and the pattern of LEDs will change.

•Press TEMPERATURE UP button, the COLD LED is on for 5-5.5kg(560mm wide).

•Press WATER LEVEL UP button, the LOW WATER LED is on for 6-6.5kg(600mm wide).

•Press SPIN SPEED UP button, the SPIN HOLD LED is on for 7-7.5kg(650mm wide).

•Press POWER to exit this mode.

SIZE SWITCH SET UP

MODE

		RINSE	FINAL SPIN
			RINSE
				ADVANCE
5- 5.5kg	6.5kg	7.5kg	O FAST
		O HOT	O HIGH O	MED
		O WARM O MED O		SLOW	POWER
		O WARM O MED O		SLOW
		O COLD O LOW O		HOLD
PRESS TEMP UP &		5.kg

	POWER TO ENTER	5.5kg	6.5kg	7.5kg	START
	POWER TO ENTER	5.5kg	SIZE	SIZE	START
	THIS MODE	SIZE	SIZE	SIZE	PAUSE
	THIS MODE
					DELAY
					START
		WASH	WATER	SPIN
		TEMP	LEVEL	SPEED
					LED on
					LED off

If the size is set incorrectly Smartdrive will have the following settings incorrect: -

•The Auto Water Levels chosen by Smartdrive may be wrong.

•The High Water Level may be wrong by as much as 40mm.

•The flow rate for inlet water, normally 3 litres per minute, may be set incorrectly.

•The wash profile controls the strength of the agitator. This could result in poor wash performance or splashing.

•Water saver settings.

-35 -

Image 40

Contents Phase 1 to 5 Smart Drive Electronic Washing MachinePhase 3 GW Phase 4 GWPhase 5 IW Phase 5 IwecoWhat PHASE, Size & Model is Your SMARTDRIVE? MW, GWTable of Contents Recycle If Smartdrive has no Power see Section HOW to Service SmartdriveIntroduction Smartdrive Servicing Quick Reference Guide Specifications ALL Terminals and Internal Parts should be Treated AS LiveInstallation InstallationRemoving Transit Restraint Inlet HosesInstallation Environment Water Supply Temperatures SafetyAccessories and Spare Parts Levelling SmartdriveSmartdrive Components Electronics Systems Phase Wiring Diagram Specifications MotorMotor Controller Module Water Level Measurement Pressure SensorDisplay Module Water Valves Installation Rotor Position SensorPump Motor Specifications PumpDiagram showing the Floating Bowl Inner and Outer BowlsDetection Of Inner Bowl Float Off Point Bowl Check Lid Switch and Out of Balance Switch Lid SwitchWater Temperature Sensing Customising Wash Cycles GW only Phase 3 to 5 only Favourite cycle GW only All PhasesSmartdrive Information Auto Water Level GW only Phase 3 to 5 only Delay Start GW only Phase 2 to 5 onlyWater Saver GW only Phase 3 to 5 only Fabric Softener Dispenser All Phases Amount of Water Used in the Water Saver RinseWash Performance Information All Phases CreasingIf Smartdrive Appears To Have No Power Smartdrive ProblemsIf Smartdrive Powers Off mid cycle Leaking FloodingNoisy Continuous Spinning or Slow Spinning Poor Wash PerformanceSiphoning Radio Frequency Interference RFIEarth Leakage It Appears Smartdrive is doing nothingOption Adjustment Mode Wash Water Temperature All PhasesRinse Options All Phases Method of Setting the Wash TemperatureEnd of Cycle Warning Beeps GW Only All Phases PhaseAuto Water Fill Level Adjustment GW only Phase Out Of Balance Recovery Adjustment GW and MW only PhaseDiagnostic Mode What WAS the Last FAULT?Test LID, OUT of BALANCE, & Size Switches To Test Pump & Water ValvesRestart RecycleLOW Water Level LED OFF = Restart OFF Medium Water Level LED on = RE-CYCLE onPage Size Setting Mode Phase 4 and 5 only Insufficient Hot Water Hot Water LED flashing User WarningsInsufficient Cold Water Cold Water LED flashing No Water Both Hot and Cold Water LEDs flashing Overloaded Product High Water LED flashingPhase 1 to Phase 4Restart and Recycle Wash Progress LEDs flashing Demonstration Mode All LEDs flashing in patterns Fault Codes GWC08 GWM08 GWL08 THC08 THM08 THL08GWC09 GWM09 GWL09 IWM09 IWL09Smartdrive Phases 1 to 5 Fault Descriptions Phase 1 to 5 Motor Controller FaultPhase 1 Communications Fault Primary Source Motor ControllerPhase 1 to 5 Display Module Fault Phase 1 to 5 Size ErrorPrimary Source Display Module Action Primary Source Display ModulePhase 4 to Phase 1 to 5 Thermistor ErrorAction Phase Phase 2 toPhase 1 to 5 Pressure Sensor Fault Phase 1 to 5 Flood Protection ErrorPhase 1 Pump Fault Primary Source Pressure TubePhase 1 Pump Connection Fault Phase 5 IW LCD Initialisation Error28 30 xx Phase 1 Display / Motor Controller out of Sequence Primary Source Pump ActionPhase 1 Brake Resistor Fault Phase 1 Pump Circuit ErrorPhase 1 MC Reset Error Phase 1 to 5 Water Leak Fault Phase 1 to 5 Pump Block ErrorPrimary Source Pump System Secondary Source Mechanical ActionPhase 1 to 5 Tap or Pressure Sensor Tube Fault Phase 1 to 5 Bowl Dis-Engaged FaultPrimary Source Mechanical Primary Source SudsPhase 1 to 5 Temperature Sensor Fault Phase 1 Rotor Fault Primary SourcePhase 1 to 5 OOB Switch Fault Primary Source Mechanical ActionPhase 2 to 5 Water in Bowl During Spin Phase 5 Display FaultPrimary Source Pump System Action Secondary Source Motor ControllerPhase 2 to 3 Bowl Dis-engaged Fault Phase 2 to 5 Hot and Cold Valve FaultPrimary Source Wiring Phase 2 to 5 Cold Valve FaultPhase 2 to 5 Hot Valve Fault Phase 5 ECO Recirculation FaultPhase 5 ECO Recirculation Fault See fault code Secondary Source Diverter ValvePhase 2 to 5 Motor / Motor Control Step Fail Phase 2 to 5 Rotor Position Sensor FaultSecondary Source Motor Phase 4 to 5 Bowl Check Fault Phase 4 to 5 Motor Controller FaultPhase 4 Motor Controller Fault Primary Source- PumpPhase 2 to 3 Display / Motor Controller Comms. Error Phase 5 Machine Setup ErrorPhase 1 to 5 Single Rotor Position Sensor Error Primary Source Wiring ActionPhase 1 to 5 Repetitive Rotor Position Sensor Error Phase 1 to 4 Single Current TripPhase 1 to 4 Repetitive Current Trip Phase 4 Single Current Trip & Rotor Position Sensor ErrorPhase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Complete Disassembly Mechanical Service SectionPhase 5 Topdeck Showing Wiring Connections Phase 2 Topdeck Showing Wiring Connections NB DON’T Remove the Earth Connection from the WrapperPage Page Assembly Guidelines Motor Assembly & Disassembly AssemblyPump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Appendix a Binary Decoding Chart 8 Bits Wash Progress LEDsFault Finding / Fault Codes Size SettingImportant Note Wiring Connections WM013 Pump Hood KIT January 2000 Phases 2 toPump Hood Kit Part Number 479188P WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only WM70 Premature OUT of Balance February 1995 Phase 2 only WM65 BIB Deflector April 1994- Phase 1 onlyKit Lever Out of Balance & Bracket Phase 2 Part Number WM80 Condensation KIT May 1996 Phase 2 & 3 only WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 toAppendix C Smarttool Appendix D Tools for Servicing Smartdrive Specifications for IW IW Quick Reference GuideModels Size Width Wash Load Capacity Compact Medium LargeIntroduction to IW Wash 1 Detergent Activating Wash Front loader type washWater Temperature Sensing Option Adjustment Mode for IW PumpOther Options Diagnostic Mode for IW Status DisplayFault Status Size Setting Mode for IW Recycle