Fisher & Paykel 517735 service manual Phase 1 Pump Circuit Error, Phase 1 Brake Resistor Fault

Page 51

32.(00100000) Phase 1 - Pump Circuit Error

The Display Module has detected that the pump is on when it is off.

Primary Source - Display Module

Action

1.Check for moisture in the console area.

2.Replace the Display Module.

33.(00100001) Phase 1 - Water Valve Fault The Module has detected a water valve fault.

Primary Source - Water Valve connection

Action - Check that both valves are connected up properly.

Secondary Source - Water Valve coil faulty

Action

1.Check the valve coils are not open circuit.

2.Replace Display Module if valve coils are not faulty.

34.(00100010) Phase 1 - Brake Resistor Fault

The circuit that controls the braking of the motor is faulty.

Primary Source - Motor Controller Action - Replace the Motor Controller

Secondary Source - Display Module Action - Replace the Display Module.

If the Display Module corrects the fault, then re-fit the original Motor Controller.

35.(00100011) Phase 1 - MC Reset Error

The Display Module has sent a false signal to the Motor Controller.

Primary Source - 12 way Harness Connection.

Action - Check the 12 way harness connection between the Display Module and the Motor Controller.

Secondary Source - Display Module Action - Replace the Display Module.

- 46 -

Image 51

Contents Smart Drive Electronic Washing Machine Phase 1 to 5Phase 5 Iweco Phase 3 GWPhase 4 GW Phase 5 IWMW, GW What PHASE, Size & Model is Your SMARTDRIVE?Table of Contents Recycle HOW to Service Smartdrive If Smartdrive has no Power see SectionIntroduction Smartdrive Servicing Quick Reference Guide ALL Terminals and Internal Parts should be Treated AS Live SpecificationsInlet Hoses InstallationInstallation Removing Transit RestraintLevelling Smartdrive Installation Environment Water Supply TemperaturesSafety Accessories and Spare PartsSmartdrive Components Electronics Systems Phase Wiring Diagram Motor SpecificationsWater Level Measurement Pressure Sensor Motor Controller ModuleDisplay Module Water Valves Rotor Position Sensor InstallationPump Pump Motor SpecificationsInner and Outer Bowls Diagram showing the Floating BowlDetection Of Inner Bowl Float Off Point Bowl Check Lid Switch Lid Switch and Out of Balance SwitchWater Temperature Sensing Favourite cycle GW only All Phases Customising Wash Cycles GW only Phase 3 to 5 onlySmartdrive Information Delay Start GW only Phase 2 to 5 only Auto Water Level GW only Phase 3 to 5 onlyWater Saver GW only Phase 3 to 5 only Amount of Water Used in the Water Saver Rinse Fabric Softener Dispenser All PhasesCreasing Wash Performance Information All PhasesSmartdrive Problems If Smartdrive Appears To Have No PowerIf Smartdrive Powers Off mid cycle Flooding LeakingNoisy Poor Wash Performance Continuous Spinning or Slow SpinningIt Appears Smartdrive is doing nothing SiphoningRadio Frequency Interference RFI Earth LeakageWash Water Temperature All Phases Option Adjustment ModeMethod of Setting the Wash Temperature Rinse Options All PhasesPhase End of Cycle Warning Beeps GW Only All PhasesOut Of Balance Recovery Adjustment GW and MW only Phase Auto Water Fill Level Adjustment GW only PhaseWhat WAS the Last FAULT? Diagnostic ModeTo Test Pump & Water Valves Test LID, OUT of BALANCE, & Size SwitchesMedium Water Level LED on = RE-CYCLE on RestartRecycle LOW Water Level LED OFF = Restart OFFPage Size Setting Mode Phase 4 and 5 only User Warnings Insufficient Hot Water Hot Water LED flashingInsufficient Cold Water Cold Water LED flashing Overloaded Product High Water LED flashing No Water Both Hot and Cold Water LEDs flashingPhase 4 Phase 1 toRestart and Recycle Wash Progress LEDs flashing Demonstration Mode All LEDs flashing in patterns IWM09 IWL09 Fault CodesGWC08 GWM08 GWL08 THC08 THM08 THL08 GWC09 GWM09 GWL09Primary Source Motor Controller Smartdrive Phases 1 to 5 Fault DescriptionsPhase 1 to 5 Motor Controller Fault Phase 1 Communications FaultPrimary Source Display Module Phase 1 to 5 Display Module FaultPhase 1 to 5 Size Error Primary Source Display Module ActionPhase 2 to Phase 4 toPhase 1 to 5 Thermistor Error Action PhasePrimary Source Pressure Tube Phase 1 to 5 Pressure Sensor FaultPhase 1 to 5 Flood Protection Error Phase 1 Pump FaultPrimary Source Pump Action Phase 1 Pump Connection FaultPhase 5 IW LCD Initialisation Error 28 30 xx Phase 1 Display / Motor Controller out of SequencePhase 1 Pump Circuit Error Phase 1 Brake Resistor FaultPhase 1 MC Reset Error Secondary Source Mechanical Action Phase 1 to 5 Water Leak FaultPhase 1 to 5 Pump Block Error Primary Source Pump SystemPrimary Source Suds Phase 1 to 5 Tap or Pressure Sensor Tube FaultPhase 1 to 5 Bowl Dis-Engaged Fault Primary Source MechanicalPrimary Source Mechanical Action Phase 1 to 5 Temperature Sensor FaultPhase 1 Rotor Fault Primary Source Phase 1 to 5 OOB Switch FaultSecondary Source Motor Controller Phase 2 to 5 Water in Bowl During SpinPhase 5 Display Fault Primary Source Pump System ActionPhase 2 to 5 Cold Valve Fault Phase 2 to 3 Bowl Dis-engaged FaultPhase 2 to 5 Hot and Cold Valve Fault Primary Source WiringSecondary Source Diverter Valve Phase 2 to 5 Hot Valve FaultPhase 5 ECO Recirculation Fault Phase 5 ECO Recirculation Fault See fault codePhase 2 to 5 Rotor Position Sensor Fault Phase 2 to 5 Motor / Motor Control Step FailSecondary Source Motor Phase 4 to 5 Motor Controller Fault Phase 4 to 5 Bowl Check FaultPrimary Source- Pump Phase 4 Motor Controller FaultPhase 5 Machine Setup Error Phase 2 to 3 Display / Motor Controller Comms. ErrorPrimary Source Wiring Action Phase 1 to 5 Single Rotor Position Sensor ErrorPhase 4 Single Current Trip & Rotor Position Sensor Error Phase 1 to 5 Repetitive Rotor Position Sensor ErrorPhase 1 to 4 Single Current Trip Phase 1 to 4 Repetitive Current TripPhase 1 to 5 Motor Stall Phase 1 to 5 Bowl Engaged During Agitate Phase 4 to 5 Brake Function Time-out Fault Mechanical Service Section Complete DisassemblyPhase 5 Topdeck Showing Wiring Connections NB DON’T Remove the Earth Connection from the Wrapper Phase 2 Topdeck Showing Wiring ConnectionsPage Page Assembly Guidelines Assembly Motor Assembly & DisassemblyPump Blockage Shaft & Bearing Removal Shaft & Bearing Assembly Page Wash Progress LEDs Appendix a Binary Decoding Chart 8 BitsSize Setting Fault Finding / Fault CodesImportant Note WM013 Pump Hood KIT January 2000 Phases 2 to Wiring ConnectionsPump Hood Kit Part Number 479188P WM51 Diagnostic Flow Chart Sept 1992- Phase 1 only WM65 BIB Deflector April 1994- Phase 1 only WM70 Premature OUT of Balance February 1995 Phase 2 onlyKit Lever Out of Balance & Bracket Phase 2 Part Number WM81 Pump Shield 5KG Smartdrive September 1996 Phases 1 to WM80 Condensation KIT May 1996 Phase 2 & 3 onlyAppendix C Smarttool Appendix D Tools for Servicing Smartdrive Compact Medium Large Specifications for IWIW Quick Reference Guide Models Size Width Wash Load CapacityWash 1 Detergent Activating Wash Front loader type wash Introduction to IWWater Temperature Sensing Pump Option Adjustment Mode for IWOther Options Status Display Diagnostic Mode for IWFault Status Recycle Size Setting Mode for IW