Airstream PNEG-343 service manual Safety First, Safety Alert Symbol, Safety Alert Decals

Page 5

SAFETY FIRST

Grain Systems, Inc.'s principle con- cern is your safety and the safety of others associated with grain han- dling equipment. This manual was written with that thought in mind. We want to keep you as a customer. This manual is to help you under-

stand safe operating proceedures and some problems which may be encountered by the operator and other personnel.

As owner and/or operator, it is your responsibility to know what re- quirements, hazards and precau-

tions exist, and to inform all person- nel associated with the equipment or who are in the dryer area. Avoid any alterations to the equipment. Such alterations may produce a very dangerous situation, where serious injury or death may occur.

The symbol shown below is used to call your attention to instructions concerning your personal safety. Watch for this symbol; it points out important safety precautions. It means "ATTENTION", "WARNING", "CAUTION", and "DANGER". Read the message that follows and be cautious to the possibility of per- sonal injury or death.

SAFETY ALERT SYMBOL

WARNING! BE ALERT!

Personnel operating or working around a dryer should read this manual. This manual must be delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse of the equipment.

Grain Systems, Inc. recommends that you contact your local power com- pany and have a representative sur- vey your dryer installation so your wir- ing will be compatible with their sys- tem and you will have adequate power supplied to your unit.

SAFETY ALERT DECALS

Safety decals should be read and understood by all people in and around the dryer area. If the follow- ing safety decals are not displayed on your dryer, or if they are dam- aged, contact Grain Systems, Inc. for replacement.

A CAREFUL OPERATOR

IS THE BEST INSURANCE

AGAINST AN ACCIDENT

5

Image 5
Contents Ryer Operation Page Table of Contents Series Dryer Operation and ServiceWarranty Safety Alert Symbol Safety FirstSafety Alert Decals Careful Operator Is the Best Insurance Against AN AccidentSafety Alert Decals Keep the Dryer Clean Do not Allow Fine Safety PrecautionsDryer Control Panel Moisture Control SwitchMoisture Control Thermostat Information regarding dryer operationDrying Mode Switch Control Power SwitchLoad Auger Switch FAN SwitchesDryer Power Stop Switch Dryer Power Start SwitchSetting the OUT Grain Timer Setting the DRY, Cool Batch and Unload TimersElectronic Monitoring Control System Turning on Electronic Monitoring Control SystemUtilizing Bushel Counter Setting the Load Unload DelaysDryer Safety Circuit Safety Circuit Shutdown Messages PRE Season Inspection Dryer PRE Start ChecksLoad Auger TWO Speed OperationONE Speed Operation Metering Roll OperationBurner Test Fire Burner SafetyEmergency Staged Batch CheckDryer Shutdown Turn the control power switch to on Continuous Flow and Continuous Batch Start UP ProcedureDryer Start UP Continuous Flow OperationFull Heat Series Continuous Flow Metering Roll SettingsDryer Start UP & Operation Dry & Cool Continuous Flow Metering Roll SettingsStaged Batch Operation Matically shut down during the cooling and unloading cycles Staged Batch FAN & Heater Switch SettingsFull Heat Dry & Cool Series Batch Timer SettingsSeries Staged Batch Timer Settings Series Service Guide Lube Procedures ServiceSeasonal Inspection and Service Insulation Class Consistency Type Grease Frame Type Suggested LubricantsClearance Holes FAN Propellor Removal and InstallationThreaded Bushing Holes FAN Motor Removal and Installation Heater Parts Removal and Installation Main Controls Metering Roll ServicingService Tool HOW to Determine a Metering Roll ProblemHOW to Clear a Jammed Metering Roll Series Wiring Diagrams INPUT/OUTPUT Board Terminal Identification Series Wiring to Control BOX Series Control Wiring Series Safety Wiring Diagram Series Front Panel Internal Wiring Series Front Panel External Wiring Dryer FAN can Control Wiring Series 220 Volt Single Phase Control Wiring Series 220 Volt 3 Phase Power Wiring Series 440 Volt 3 Phase Power Wiring Problem Possible Cause Trouble Analysis ProcedureDisplay shows Burner 1, 2 or 3 Warning Flame May not be turning. The air switch may need adjustment Problem Possible Cause Trouble Analysis Procedure Change the marquee on the LCD dis- play Press the enter button when desired setting is reachedQuick Reference Guide Page