Airstream PNEG-343 Dryer Start UP & Operation, Series Continuous Flow Metering Roll Settings

Page 19

DRYER START UP & OPERATION

1300 SERIES CONTINUOUS FLOW METERING ROLL SETTINGS

				Full Heat

Initial	Moisture	Approx.		2 Speed	2 Speed
Moisture	Removed	Dry Time	1 Speed	Low	High
17%	2 pts.	16 min.	625	317	875
18%	3 pts.	21 min.	476	270	775
19%	4 pts.	26 min	385	241	675
20%	5 pts.	31.5 min.	317	213	575
21%	6 pts.	37 min.	270	196	476
22%	7 pts.	41.5 min.	241	185	385
23%	8 pts.	47 min.	213	172	317
24%	9 pts.	51 min.	196	161	270
25%	10 pts.	54 min.	185	150	241
26%	11 pts.	58 min.	172	140	213
27%	12 pts.	62 min.	161	132	196
28%	13 pts.	66.5 min.	150	123	185
29%	14 pts.	71.5 min.	140	116	172
30%	15 pts.	76 min.	132	110	161
31%	16 pts.	81 min.	123	104	150
32%	17 pts.	86 min.	116	100	140
33%	18 pts.	91 min.	110	096	132
34%	19 pts.	96 min.	104	087	123
35%	20 pts.	100 min.	100	082	116

These are approximate starting points.

19

Image 19

Contents Ryer Operation Page Table of Contents Series Dryer Operation and ServiceWarranty Careful Operator Is the Best Insurance Against AN Accident Safety FirstSafety Alert Symbol Safety Alert DecalsSafety Alert Decals Keep the Dryer Clean Do not Allow Fine Safety PrecautionsInformation regarding dryer operation Moisture Control SwitchDryer Control Panel Moisture Control ThermostatFAN Switches Control Power SwitchDrying Mode Switch Load Auger SwitchDryer Power Stop Switch Dryer Power Start SwitchTurning on Electronic Monitoring Control System Setting the DRY, Cool Batch and Unload TimersSetting the OUT Grain Timer Electronic Monitoring Control SystemDryer Safety Circuit Setting the Load Unload DelaysUtilizing Bushel Counter Safety Circuit Shutdown Messages PRE Season Inspection Dryer PRE Start ChecksMetering Roll Operation TWO Speed OperationLoad Auger ONE Speed OperationBurner Test Fire Burner SafetyDryer Shutdown Staged Batch CheckEmergency Continuous Flow Operation Continuous Flow and Continuous Batch Start UP ProcedureTurn the control power switch to on Dryer Start UPDryer Start UP & Operation Series Continuous Flow Metering Roll SettingsFull Heat Dry & Cool Continuous Flow Metering Roll SettingsStaged Batch Operation Matically shut down during the cooling and unloading cycles Staged Batch FAN & Heater Switch SettingsFull Heat Dry & Cool Series Batch Timer SettingsSeries Staged Batch Timer Settings Series Service Guide Seasonal Inspection and Service ServiceLube Procedures Insulation Class Consistency Type Grease Frame Type Suggested LubricantsThreaded Bushing Holes FAN Propellor Removal and InstallationClearance Holes FAN Motor Removal and Installation Heater Parts Removal and Installation Main Controls Metering Roll ServicingHOW to Clear a Jammed Metering Roll HOW to Determine a Metering Roll ProblemService Tool Series Wiring Diagrams INPUT/OUTPUT Board Terminal Identification Series Wiring to Control BOX Series Control Wiring Series Safety Wiring Diagram Series Front Panel Internal Wiring Series Front Panel External Wiring Dryer FAN can Control Wiring Series 220 Volt Single Phase Control Wiring Series 220 Volt 3 Phase Power Wiring Series 440 Volt 3 Phase Power Wiring Problem Possible Cause Trouble Analysis ProcedureDisplay shows Burner 1, 2 or 3 Warning Flame May not be turning. The air switch may need adjustment Problem Possible Cause Trouble Analysis Procedure Quick Reference Guide Press the enter button when desired setting is reachedChange the marquee on the LCD dis- play Page