Airstream PNEG-343 service manual Continuous Flow Metering Roll Settings, Dry & Cool

Page 20

DRYER START UP & OPERATION

CONTINUOUS FLOW METERING ROLL SETTINGS*

				Dry & Cool

Initial	Moisture	Approx.		2 Speed	2 Speed
Moisture	Removed	Dry Time	1 Speed	Low	High
17%	2 pts.	18 min.	363	187	650
18%	3 pts.	24 min.	272	163	550
19%	4 pts.	30 min	218	145	450
20%	5 pts.	35 min.	187	131	363
21%	6 pts.	40 min.	163	119	272
22%	7 pts.	45 min.	145	109	218
23%	8 pts.	50 min.	131	101	187
24%	9 pts.	55 min.	119	093	163
25%	10 pts.	60 min.	109	087	145
26%	11 pts.	65 min.	101	082	131
27%	12 pts.	70 min.	093	077	119
28%	13 pts.	75 min.	087	073	109
29%	14 pts.	80 min.	082	069	101
30%	15 pts.	85 min.	077	065	093
31%	16 pts.	90 min.	073	061	087
32%	17 pts.	95 min.	069	057	082
33%	18 pts.	100 min.	065	053	077
34%	19 pts.	105 min.	062	049	073
35%	20 pts.	110 min.	059	045	069

These are approximate starting points.

20

Image 20

Contents Ryer Operation Page Series Dryer Operation and Service Table of ContentsWarranty Safety First Safety Alert SymbolSafety Alert Decals Careful Operator Is the Best Insurance Against AN AccidentSafety Alert Decals Safety Precautions Keep the Dryer Clean Do not Allow FineMoisture Control Switch Dryer Control PanelMoisture Control Thermostat Information regarding dryer operationControl Power Switch Drying Mode SwitchLoad Auger Switch FAN SwitchesDryer Power Start Switch Dryer Power Stop SwitchSetting the DRY, Cool Batch and Unload Timers Setting the OUT Grain TimerElectronic Monitoring Control System Turning on Electronic Monitoring Control SystemUtilizing Bushel Counter Setting the Load Unload DelaysDryer Safety Circuit Safety Circuit Shutdown Messages Dryer PRE Start Checks PRE Season InspectionTWO Speed Operation Load AugerONE Speed Operation Metering Roll OperationBurner Safety Burner Test FireEmergency Staged Batch CheckDryer Shutdown Continuous Flow and Continuous Batch Start UP Procedure Turn the control power switch to onDryer Start UP Continuous Flow OperationFull Heat Series Continuous Flow Metering Roll SettingsDryer Start UP & Operation Continuous Flow Metering Roll Settings Dry & CoolStaged Batch Operation Staged Batch FAN & Heater Switch Settings Matically shut down during the cooling and unloading cyclesSeries Batch Timer Settings Full Heat Dry & CoolSeries Staged Batch Timer Settings Series Service Guide Lube Procedures ServiceSeasonal Inspection and Service Suggested Lubricants Insulation Class Consistency Type Grease Frame TypeClearance Holes FAN Propellor Removal and InstallationThreaded Bushing Holes FAN Motor Removal and Installation Heater Parts Removal and Installation Metering Roll Servicing Main ControlsService Tool HOW to Determine a Metering Roll ProblemHOW to Clear a Jammed Metering Roll Series Wiring Diagrams INPUT/OUTPUT Board Terminal Identification Series Wiring to Control BOX Series Control Wiring Series Safety Wiring Diagram Series Front Panel Internal Wiring Series Front Panel External Wiring Dryer FAN can Control Wiring Series 220 Volt Single Phase Control Wiring Series 220 Volt 3 Phase Power Wiring Series 440 Volt 3 Phase Power Wiring Trouble Analysis Procedure Problem Possible CauseDisplay shows Burner 1, 2 or 3 Warning Flame May not be turning. The air switch may need adjustment Problem Possible Cause Trouble Analysis Procedure Change the marquee on the LCD dis- play Press the enter button when desired setting is reachedQuick Reference Guide Page