JVC Explore Specifications and Features of KD-SH9101 and KD-SH9104 Models

Page 75

SPECIFICATIONS

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front:	50 W per channel
Rear:	50 W per channel
Continuous Power Output (RMS):
Front:	19 W per channel into 4 Ω, 40 Hz
	to 20 000 Hz at no more than
	0.8% total harmonic distortion.
Rear:	19 W per channel into 4 Ω, 40 Hz
	to 20 000 Hz at no more than
	0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range:
Frequencies: 60 Hz, 150 Hz, 400 Hz,
	1 kHz, 2.4 kHz, 6 kHz, 12 kHz
Level:	±10 dB

Frequency Response: 40 Hz to 20 000 Hz

Signal-to-Noise Ratio: 70 dB

Line-In Level/Impedance:

LINE IN: 1.5 V/20 kΩ load

Line-Out Level/Impedance:

4.0V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:

FM: 87.5 MHz to 108.0 MHz

AM: (MW)	522 kHz to 1 620 kHz
(LW)	144 kHz to 279 kHz

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 ∝V/75 Ω)

50dB Quieting Sensitivity: 16.3 dBf (1.8 ∝V/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 30 dB

Capture Ratio: 1.5 dB

[MW Tuner]

Sensitivity: 20 ∝V

Selectivity: 35 dB

[LW Tuner]

Sensitivity: 50 ∝V

CD PLAYER SECTION

Type: Compact disc player

Signal Detection System: Non-contact optical pickup (semiconductor laser)

Number of channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Dynamic Range: 98 dB

Signal-to-Noise Ratio: 102 dB

Wow and Flutter: Less than measurable limit MP3 (MPEG Audio Layer 3)

Max. Bit rate: 320 Kbps WMA (Windows Media® Audio)

Max. Bit rate: 192 Kbps

GENERAL

Power Requirement:

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)

Grounding System: Negative ground Allowable Operating Temperature:

0°C to +40°C

Dimensions (W ⋅ H ⋅ D):

Installation Size:

182 mm ⋅ 52 mm ⋅ 161 mm Panel Size:

188 mm ⋅ 58 mm ⋅ 17 mm Mass: 1.8 kg (excluding accessories)

Design and specifications are subject to change without notice.

ENGLISH

75

Image 75

Contents KD-SH9104/KD-SH9103 KD-SH9102/KD-SH9101 How to reset your unit Position And Reproduction Of LabelsSee Contents Location of the Buttons Control panelIllumination Navigation for easy operations FM/DAB Remote controllerPlace the battery Preparing the remote controllerInstalling the battery Remove the battery holderBasic Operations Turning on the powerTo drop the volume in a moment To turn off the powerCanceling the display Setting the clockDemonstration Selecting the level meter StandardMeter Press ¢ to search stations of higher frequencies Radio OperationsSearching a station automatically Auto search Select the band FM1 3, AM Start searching a stationSearching a station manually Manual search Select the band FM1 3, AMPress SRC source Start SSM FM station automatic preset SSMStoring stations in memory ReceivePress and hold the number button Manual presetSelecting a preset station directly Tune in to a station in this example, of 92.5 MHzProgramme station PS name is Emphasized*3 Selecting a preset station using the preset station listSelect the number 1 6 for the preset station you want Initial display patternRDS Operations What you can do with RDSTo use Network-Tracking Reception Alternately Using TA Standby ReceptionPTY Stnby standby setting screen Appears on the display ReceptionSelect one of the twenty-nine PTY Using PTY Standby ReceptionTo select your favorite PTY code for PTY Standby Reception To set PTY Standby ReceptionTo search your favorite programme type, see Searching your favorite programmeTo store your favorite programme types To store your favorite programme types, seeEx. When Rock M is selected Select one of the twenty-nine PTY codes. SeeStart PTY search for your favorite programme Setting the TA volume level Automatic clock adjustmentTo activate programme search, follow the procedure below Same programme can be received on different frequencies PTY codesTo stop play and eject the disc CD OperationsPlaying a disc About MP3 and WMA discsTo return the control panel to its previous Display indications when inserting anDisplay indications when inserting an Audio CD or a CD Text MP3 or a WMA discTo go to the next or previous tracks What is ImageLinkLocating a particular portion on a track To fast-forward or reverse the trackHow to go to the desired track quickly Locating a track on a discTo go to a track quickly Locating a folder on a disc To go to a folder directlyTo skip to the next or previous folder Only on the remote controller Select the number 1 6 for the track To select a track and start playbackTo select a folder and start playback FolderRandom Folder Random Disc Random Off Selecting playback modesTo play back tracks repeatedly Repeat Play Random Disc Random OffTo play back only intros Intro Scan Prohibiting disc ejectionWhile playing an audio CD or a CD Text disc Initial display While playing an MP3 or a WMA disc Initial displaySelecting the DSP modes DSP OperationsTo make further precise settings for the DSP modes Adjust the DSP effect level-1, 2, orPress SEL select once to show the DSP mode selection screen Select your listening seats position Further precise setting screenTo go back to the DSP mode selection screen Press number button 6 to enterPress SEL select twice to show the sound selection screen Equalizer OperationsOne of the sound modes listed on DisplayStore the adjustment you made Enter the sound adjustment modeIf you want to cancel the adjustment Canceled Vol Adj BBE Sub Out Sound AdjustmentsSettings Adjust the levelTo increase the level BBE Off BBE 1 BBE 2 BBE 3 CanceledTo adjust the input level of each source Vol Adj To make sounds natural-BBERetouch and edit the images Install / Start the programGraphic Displays Import the imagesPress Mode M after the disc is detected Downloading images and animationsPress number button 6 to show the download selection screen As follows Folder name If you want to cancel the procedure, pressFile name ListIf it is OK, press number button 1 to start downloading Deleting unwanted filesTo delete all the stored files at a time Select a file you want to downloadPress the number buttons for the file you want to delete To delete the file stored PowerOn, PowerOff,To delete the stored files for Picture one by one Animation appears, and the unit asks you Delete OK?Press Disp D to resume Source indication screen Select UserSelect UserPict To cancel all graphic displays, select OffTo select a still image for graphic display-User Picture Select UserMovie, UserSlide, or UserPictOther Main Functions Basic ProcedureAdjust Adjust the PSM item selectedPreferred Setting Mode PSM items To select the scroll mode-Scroll To adjust the display contrast level ContrastTo show the graphics on the display- Graphics To select the source animation on the display-KeyIn CFMTo select the font on the display Font Type To turn on/off the line input switch LineTo turn on/off the power amplifier switch- PowerAmp LCD TypeSelecting the dimmer mode Select From- To to set the timer for the dimmer modePress ¢ Or 4 to select Dimmer Set the timer Sources Maximum number Characters Select a characterMove the cursor to the next Until you finishChanging the control panel angle Press and hold 0 until the angle adjustment screen appearsAdjust the angle to the position you want When using the remote controllerDetaching the control panel Attaching the control panelUnlock the control panel Select the CD automatic changer When the current disc is an audio CD or a CD Text discCD Changer Operations Playing discsTo go to the next track or the previous tracks When the current disc is an MP3 discTo go to a particular disc directly To change the display patternPress Mode M while playing If the folder does not contain any MP3 tracks, it is skipped To select a disc using the disc lists Select the number 1 6 for the disc you want to playDisplay can show only six names at a time Random Folder Random Disc Random Off Random All To play back tracks at random Random PlayIntro Track Intro Disc Intro Off Repeat Track Repeat Disc Repeat OffRepeat Folder Repeat DiscFor the DSP modes, see Playing an external component 3 Adjust the volumeExternal Component Operations Select the external component LineSelect the DAB band DAB1, DAB2, or DAB3 What is DAB system?DAB Tuner Operations Select the DAB tunerStart searching for an ensemble When noises generated while runningTo tune in to a particular ensemble without searching Interfere with your listeningSource, the power automatically Storing DAB services in memoryTuning in to a preset DAB service On page 7. When you select aSelecting a preset service using the preset service list Service you wantSelect the number 1 6 for a How Road Traffic Flash Standby Reception works Using Announcement Standby ReceptionWhat you can do more with Road Traffic Flash Standby ReceptionTo activate Announcement Standby Reception Selected announcementDisplay and is stored into memory Etc ANN announcement indicator either lights up or flashesHow Announcement Standby Reception works Announcement typeWhile receiving an FM RDS station Searching your favorite serviceWhile receiving a DAB service To use Alternative ReceptionChanging the display pattern Available characters Sound modes preset frequency level settingsSound Preset equalizing values Mode Additional InformationSymptoms Causes Remedies TroubleshootingCD Changer Graphics MP3/WMA Playback Handling discs MaintenanceLW Tuner SpecificationsFM Tuner MW TunerHaving Trouble with operation? Voordat u aan de montage van het apparaat Gerät geliefert HinweisRemarque Die folgenden Teile werden zusammen mit diesemEnglish Deutsch Français Nederlands Verbind ze aan de versterker Disconnect the speakers from this unitKoppel de speakers van dit apparaat los en Connect them to the amplifier. Leave