StreamLight VF-PS1 Case of adopting external braking resistor Optional, VFPS1-4300PLE~4900PLE

Page 19

E6581429

QVFPS1-4300PLE~4900PLE

A switch or switches enable to reduce grounding capacitance.

Large Small

*2

Large Small

*2: VFPS1-4300PLE have two switches.

For details, refer to main circuit terminal

QVFPS1-4007PDE~4220PDE There is no switch.

QVFPS1-4300PDE~4900PDE

A switch enables to reduce grounding capacitance.

Large Small

Large Small

To change the capacitance from small to large, push in the button.

(Factory default position)

To change the capacitance

from large to small, pull up1 the button.

To change the capacitance from small to large, slide the switch in direction shown left. (Factory default position)

To change the capacitance from large to small, slide the switch in direction shown left.

1.3.4 In case of adopting external braking resistor (Optional)

To wire for external braking resistor, an attention is needed because PA/+ terminal have a wiring to the internal DC reactor. Refer to followings when you wire for external braking resistor.

Q0.75~22kW

With reference of the figure right, make the each solderless terminal in back to back and fasten them with the screw.

PA/+ terminal screw

Wiring to the internal DC reactor

Wiring to the external braking resistor

Q30~90kW

Fasten with the screw both of copper bar connected to the PA/+ terminal and the stripped cable for external braking resistor.

A-13

Image 19
Contents Tosverttm VF-PS1 Page Transportation & installation Safety precautionsII. Introduction Contents Page This manual E6581386 Contents of the product codeRead first Check the productNames and functions Outside view Structure of the main bodyTo 5 F1 to F4 function keys STOP/RESET key The drive stops operationOperation panel LCD panelFWD About changing parameter settingsMain circuit terminal VFPS1-4037PDE, 4055PDE VFPS1-4150PLE PO PA/+ PE PO PA/+ PB PC/- PE PA/+ Front cover Detaching the coverCharge lamp Grounding capacitor switching methodVFPS1-4007PLE~4220PLE VFPS1-4300PLE~4900PLE Case of adopting external braking resistor OptionalHow to install Installation Installation environmentConnection of equipment Standard connections Standard connection diagram sink logicStandard connection diagram source logic Connection with peripheral equipment Power supply and motor connectionsDescription of terminals Main circuit terminalsOperations Settings to be made at first power onLanguage Selection window appears Status Monitor Mode Setting/monitor modesTop View Mode Parameter Setup ModeExplanation of the top window Operation in Top View ModeSetting a panel operation frequency Press the control dialUsing an Easy key function Performing jog run Selecting a language to be displayedPress the F2 Lng key Select/confirm the desired language with the control dialPress the F4 key to carry out jog run Emergency stop / reset operationPress the STOP/RESET key Then press the STOP/RESET key againThis window, settings can be changed Searching and setting parametersSelect/confirm History function using the control dial When Quick mode is selectedF1 F2 F3 Setting a basic parameterSelect/confirm Basic parameters using the control dial Ex. Select/confirm Command input mode and Base frequencySelect/confirm Extended parameters using the control dial Setting an extended parameterChange the parameter setting CMOd Select/confirm Changed Parameters using the control dialItems displayed Description Display of details Monitoring the operation statusDisplaying details of an item monitored Select/confirm the desired item using the control dialFunction key Display Reference Position List of function key functionsPage Measures to satisfy the standards How to cope with the CE standardsMeasures to satisfy the EMC directive RES, PWR, no Ex. Countermeasure inverter wiring PLE typePDE typeWiring port plate PLE type PDE type Conforming to UL Type Measurements to be taken to satisfy the UL/CSA standardsSelection of peripheral devices Selection of wiring materials and devicesRated current a AC-1 Selection of wiring equipmentPWM Table of parametersPage Models and their standard specifications SpecificationsOverleaf LCD Outside dimensions and weight Outside dimensions and massOutline drawing Fig. C Fig. G