MasterCraft 2009 MariStar X-Series owner manual Underway, Stopping

Page 42

Reverse: Raise the lifter ball under the lever knob and briskly pull the control lever back into the forty-five (45) degrees of travel. Throttle movement will begin after forty-five (45) degrees.

Once the shift has been completed, continue to move the control lever slowly in the desired direction to increase speed.

NOTE: When shifting from forward to reverse or reverse to forward, be sure to stop the control lever in the neutral posi- tion and allow the engine to fall between 600-800 RPM before completing the shift.

Underway

If the oil pressure gauge indicates low or no oil pressure, im- mediately stop the boat as outlined below and check the oil level. If the temperature gauge indicates overheating, immediately stop the boat as outlined below and check the raw water impeller for blockage. DO NOT operate the boat until the cause for the warning has been found and corrected.

Continued operation after the warning light has illuminated may cause severe engine damage. This will void your warranty.

Stopping

Step 1: Slowly bring the control lever to the neutral position. If the boat has been driven for a long period of time or at high speed, allow the engine a 2-3 minute cool-down period at low idle (600-800 RPM).

Step 2: Turn the ignition key to the OFF position to stop the engine.

Step 3: If any problems were encountered during operation, have the boat inspected by an authorized MasterCraft dealer. Request any necessary repairs before resuming operation of the boat.

MasterCraft 2009 Owner’s Manual - Page 9-2

Image 42

Contents 2009 MasterCraft Welcome aboard Page 2-1 Page 16-2, 16-5, Page Table of contents Boating safety General PrecautionsRequired Equipment Safety EquipmentSafety Afloat Recommended EquipmentSkiing and Wakeboarding Safety Operator’s License Common sense approach Rules of the open water Sailing Vessel Right-of-Way OvertakingOther Special Situations Fishing Vessel Right-of-WayGuide to individual models Exhaust Bow Light Transom Drain Plug MariStar Fuel Tank Engine Batteries Filler Star CSX Instrument panels Measurements All Models-Actual Switch Usage Will Vary Accessory SwitchesAft Light Switch Volt ReceptacleAttitude Adjustment or Trim Tab Switch MariStar 230, X-30, MariStar 245 MariStar 280Blower Switch Ballast Empty/Fill SwitchesManual and Automatic Bilge Pump Switch Manual Circuit BreakersDisplay Selector Switch Clock Adjustment SwitchCourtesy Lights Switch Dual Battery Operation SwitchEngine Oil Pressure Gauge Engine Hatch SwitchEngine Synchronizing Switch MariStar 280/X-80, CSX-220, CSX-265Low Voltage Battery Alarm Heater SwitchInstrument Panel Gauge Backlighting Switch Fuel GaugeRefrigerator Switch Navigation/Anchor Lights SwitchOther Alarms Seat Heat SwitchesTemperature Gauge Shower and/or Slick Boot SwitchSink Switch Shift/Throttle ControlTower Lights Switch Video Display GaugePage Wash Down Switch VoltmeterUsing care when fueling What Type of Gasoline To UseWhen Fuel Runs Out or Too Low for Proper Operation When the Boat Is Not Used for a WhileUsing Oxygenated Fuels or Fuels with Alcohol Fuels Outside United States and CanadaPage During Operation Safety checks and servicesBefore Each Operation After Operation New boat break-in First Hours of Operation After Break-In Page Before Starting Starting the EngineShifting Gears Underway StoppingOperational hints Page Unusual Operating Conditions Docking and Tie-UpLifting the boat Using Lifting EyesUsing Lifting Slings Storage CradleGalvanic Corrosion Corrosion preventionMarine Growth Stainless Steel and ChromeCleaning the boat HullUpholstery Fiberglass Swim Platform CarpetTeak Wood WindshieldUnacceptable Upholstery Cleaners Slick BootAcceptable Upholstery Cleaners Enclosed HeadApco Mastercraft boat care products MasterCraft Cleaning & Detailing Kit MasterCraft Microfiber Detailing ClothsMasterCraft Marine Motor Oil & Filters Before Each Use Frequency and Scheduled MaintenanceNew Boat Break-In After Each UseQuarterly Every Fifty 50 Hours Annually Every One Hundred 100 HoursCheck Raw Water Intake Strainer where equipped Inspect the Battery Connections and Hold-DownsBy the warranty Inspect the Propeller Shaft Log for Water EntryInspect the Fuel System for Leaks Inspect the Exhaust System for LeaksCheck That the Battery Is Fully Charged General Cleaning and StorageLubricate the Engine Starter Gear and Shaft Check the Engine MountsCheck the Propeller Shaft Coupling Alignment Inspect the Exhaust Flaps for DamageLubricate the Steering System Lubricate the Shift and Throttle System Check the Ballast Pump ImpellerInspect the Complete Fuel System for Leakage Fire Extinguisher and Suppression Units General Power Package Preparation General PreparationFuel System Treatment Other Winterization Preparations Ballast System Preparations Re-Activating the Boat After StorageChecking/Repairing Propellers Changing PropellersBattery Charger Comfort and convenienceAnchor and Windlass Coolers Fire Suppression and ExtinguishingGPS and Chartplotter HeadHeater Before operationLivewell/Kill Box/Catch Box Hydraulic Steering SystemLighting RefrigerationSeat Heaters Shower or Wash DownSwim/Boarding Platforms Stereo EquipmentTables Folding Down the PlatformTowers Video ScreenWater Heater Guide to troubleshooting Limited warranty statement Page Page Page Warranty registration and transfer Warranty Registration TransferService log Every 100 Hours DateIndex 12-1Gauge, Voltmeter Gauges & Switches, Variations Platforms, Swim/Boarding 19-7 Storage & Winterization 17-1 19-9 Transfer, Warranty Registration 22-1 ProStar MariStar Series Saltwater Series