Fostex owner manual VM08 Initial State

Page 11

Model VM08 Owner’s Manual

VM08 Initial State

The following explains what to do the first time you use the VM08 right out of the shipping carton. When the AC adaptor is plugged into the AC wall outlet and the power cord plugged into the DC IN connector, power will be applied and the VM08, and the display/operating panel lamps will light in the modes explained below. This is the same sa when the CPU is reset by pressing the RESET switch.

* Character display section:

* MASTER fader section:

Following the <<FOSTEX>> -> <<VM08>> display, [Init.Mix] will be displayed. If the INPUT fader/MAS- TER fader is manipulated in this state, [E] will be lit behind the [Init.Mix] display (Refer to next page).

The MASTER fader position is in- dicated by numbers 00 ~ 99. The initial setting is [00] which is the initial mix setting (The fader [MIN] position).

*Scene number display section:

The current active scene number (00 ~ 20) is displayed.

In the initial setting, [00] will be dis- played.

*Channel fader display section:

After entering the channel param- eter edit mode, the INPUT fader position of the channel selected by the CH ON/CH SEL key will be in- dicated by numbers 00 ~ 99. In the initial state, nothing is dis- played. For details, refer to [Chan- nel parameter edit mode] on page 14.

* Level display section:

In the channel parameter edit mode and fader adjust mode, the signal level input to each INPUT jack for channels 1 ~ 8 will be indicated by the pre-fader. In other words, regardless to theINPUT fader set position, the input signal level will be constantly displayed. Because, INPUT of channels 1 ~ 4 must handle low level signals such as from a microphone, a TRIM knob is provided for each chan- nel to adjust the gain. The best gainlevel can be obtained by watching this display. Channels L and R display indicates sig- nal levels at the STEREO OUT L, R jacks but in the initial state, the level meter will not fluctuate since the MASTER fader is set to the [MIN] position. Should the input and output signal levels reach the [OL] (over load) level, the sound will dis- torted, so care must be taken in adjust- ing the TRIM adjust/INPUT fader.

SCENE NO.

CH

MASTER

 

OL

 

MAX

 

R

1

 

 

 

6

 

 

12

 

 

24

 

 

48

 

L

1 2 3 4 5 6

7 8 L R

MIN

 

EQ

* Status indicator:

The dot selected by the chan- nel parameter edit mode will light but nothing lights in the initial state. Refer to [Chan- nel parameter edit mode] on page 14 for details.

* CH ON/CH SEL key:

The channel to be edited can be selected with this key in the channel parameter edit mode and, in other modes, each channel can be switched ON/ OFF. In the initial state, all channels will be indi- cated as ON and the key LED's will all light.

< Please remember this! >

*The scene number of the sber of the ssber of the scene memory which the user can setup are [00] ~ [20] but the preset scene [00] cannot be changed. Refer to page 24 for details on the scene memory.

*If, for some reason, you would like to return the VM08 setting to the factory default figure, refer to [Reset of VM08] on page 6.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Safety Instructions Table of Contents Names and Functions Level adjust key Contrast adjusting knobStatus indicator Fader adjust keyPlease remember this Reset of VM08Internal battery for the memory back up Remove the insulation paperInput 5/6 Input 7/8 jacks Peripheral Equipment ConnectionST.OUT L, R jack Input 1 ~ 4 jacksAUX Send OUT 1/2 jack Input 5/6 7/8 and AUX Send 1/2 jacksInput 5/6, Input 7/8 jacks Example-4 To use as a small facility mixer Application ExampleExample-2 To use as a Mono IN/STEREO OUT effects Example-3 For use as a sub-mixer for a live keyboard playerExample-8 As a practice aid for your musical instruments Example-5 For one take live studio recordingExample-6 To produce original Remix Example-7 To do you own Sound Track Video EditingVM08 Initial State Master fader display section Normal Mix ModeUseful information Character display sectionTo set to the present fader position To return to the setting before switching off powerSetting before switch off of power Mute of the various input channel/master outputNumber is adjusted with the Data encoder Channel Parameter Edit ModeSetup method for PAN setting Number is set with the Data encoder Setup method for EQ settingSetup method of the Effect Send level Example Character display section when LO is made to lightExample The character display section with light up A1 Setup method of the AUX Send levelExample Character section when E1 is lit Example The character display section with E1 is lit PRE/POST setup method for Effect SEND/AUX SendP. Fostex Advanced Signal Processing Technology Effect Edit ModeAbout the effect types Effect types preset for EFFUse the Data encoder to select the effect type When the EFF 1 key is pressedWhen the EFF 2 key is pressed Selecting the effect typeTo mute the effect sound Effect parameter settingsTo cancel muting Muting an effectEffect parameter details Flanger effect parameters parameter type Flange Delay pitch effect parameters parameter type Delay PitchDoubling effect parameters parameter type Doubling Chorus effect parameters parameter type ChorusPress the Scene Store key Scene Memory ModeStoring a scene memory Recalling a scene memoryPress the Fader Adjust key Level adjustFader adjust Press the Level Adjust keyPress the EFF 1 key or EFF 2 key Directly recalling a scene memoryClearing a scene memory Hold down the Exit key and press the Scene Recall keyDetails of the setup menu Setup ModeMaking settings in setup mode Foot Switch setting Display Foot Sw ? Fader Fix setting Display FaderFix ?Channel fader recall setting Display ChFdrRcl ? Master fader recall setting Display MsFdrRcl ?AUX Send 1/2 SpecificationsInput 1 ~ Input 5/6 ~ 7/8Declaration of EC Directive
Top Page Image Contents