Fostex VM08 owner manual Setup method for EQ setting, Setup method of the Effect Send level

Page 15

Model VM08 Owner’s Manual

Setup method for EQ setting

Individual setup of the low region (LO), mid region (MID) and high region (HI) for the signals of channels 1 ~ 4, 5/6, 7/8 and STEREO MASTER.

<Useful information!>

The equalizer specs of VM08 are, 100Hz +/- 18dB (shelving type) for LO-EQ, 1kHz +/- 18dB (peak- ing type) for MID-EQ, and 10kHz +/- 18dB (shelving type) for HI-EQ. Each can be adjusted in 1dB steps.

1.[LO], [MID] or [HI] dots in the status display section will light by successively pressing the PAN/EQ key.

The LCD display will show the following:

Example: Character display section when [LO] is made to light.

[1-LO: 0] will be displayed. In this condition, LO- EQ of channel 1 can be adjusted and is the indica- tion that the present LO-EQ setting is flat (0dB).

Blinking

Lit

2.The channel you wish to adjust is selected by pressing the desired CH ON/CH SEL key.

The selected channel CH ON/CH SEL key will blink.

3.The number is set with the DATA encoder.

The number will change in the range of [-18dB] ~ [+18dB] and the equalized sound will also change. The graphic display will also change at the same time.

[+18] ~ [+1] ~ [0] ~ [-1] ~ [-18] will be displayed.

Digit will move up and down.

<Useful information!>

When channels 5/6 and 7/8 are selected, the two channels will be simultaneously equalized. If MASTER is selected, both L and R will be equal- ized at the same time.

Setup method of the EFFECT SEND level

In the following, the effects send level of the signal in the channel to which effects is to be applied is adjusted before sending it to the DSP multi-effects (EFF 1/EFF 2) contained in the VM08. It is also possible for the effect send signal to select either POST (post fader) or PRE (pre- fader). The VM08 is set to POST (post fader) in the initial state.

<Useful information!>

*The EFFECT SEND signal adjusted in channels 1 ~ 4, 5/6 and 7/8 is sent to the VM08 internal DSP multi-effects (EFF1 or EFF 2). The operating explanation used here is based on the effects type ([Norm. HALL] in EFF 1, [CHORUS] in EFF 2) which are preset in EFF 1/EFF 2. Twenty-eight preset effects for EFF 1 and 38 types for EFF 2 are provided in the VM08.

To select other effects or adjust effect parameters, refer to [Effect edit mode] on page 18.

*Because EFFECT SEND is set in the post fader (the signal controllable by the INPUT fader) in the initial state, in this explanation it is necessary for the INPUT fader to be raised on the channel in which the EFFECT SEND level is to be adjusted. In addition, the MASTER fader to adjust output level from ST OUT L, R is also raised. To setup of the EFFECT SEND PRE/POST, see page 17.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model Safety Instructions Table of Contents Names and Functions Level adjust key Contrast adjusting knobStatus indicator Fader adjust keyPlease remember this Reset of VM08Internal battery for the memory back up Remove the insulation paperInput 5/6 Input 7/8 jacks Peripheral Equipment ConnectionST.OUT L, R jack Input 1 ~ 4 jacksInput 5/6 7/8 and AUX Send 1/2 jacks Input 5/6, Input 7/8 jacksAUX Send OUT 1/2 jack Example-4 To use as a small facility mixer Application ExampleExample-2 To use as a Mono IN/STEREO OUT effects Example-3 For use as a sub-mixer for a live keyboard playerExample-8 As a practice aid for your musical instruments Example-5 For one take live studio recordingExample-6 To produce original Remix Example-7 To do you own Sound Track Video EditingVM08 Initial State Master fader display section Normal Mix ModeUseful information Character display sectionTo set to the present fader position To return to the setting before switching off powerSetting before switch off of power Mute of the various input channel/master outputChannel Parameter Edit Mode Setup method for PAN settingNumber is adjusted with the Data encoder Number is set with the Data encoder Setup method for EQ settingSetup method of the Effect Send level Example Character display section when LO is made to lightSetup method of the AUX Send level Example Character section when E1 is litExample The character display section with light up A1 Example The character display section with E1 is lit PRE/POST setup method for Effect SEND/AUX SendP. Fostex Advanced Signal Processing Technology Effect Edit ModeAbout the effect types Effect types preset for EFFUse the Data encoder to select the effect type When the EFF 1 key is pressedWhen the EFF 2 key is pressed Selecting the effect typeTo mute the effect sound Effect parameter settingsTo cancel muting Muting an effectEffect parameter details Flanger effect parameters parameter type Flange Delay pitch effect parameters parameter type Delay PitchDoubling effect parameters parameter type Doubling Chorus effect parameters parameter type ChorusPress the Scene Store key Scene Memory ModeStoring a scene memory Recalling a scene memoryPress the Fader Adjust key Level adjustFader adjust Press the Level Adjust keyPress the EFF 1 key or EFF 2 key Directly recalling a scene memoryClearing a scene memory Hold down the Exit key and press the Scene Recall keySetup Mode Making settings in setup modeDetails of the setup menu Foot Switch setting Display Foot Sw ? Fader Fix setting Display FaderFix ?Channel fader recall setting Display ChFdrRcl ? Master fader recall setting Display MsFdrRcl ?AUX Send 1/2 SpecificationsInput 1 ~ Input 5/6 ~ 7/8Declaration of EC Directive
Top Page Image Contents