Fostex VM08 owner manual Effect parameter details

Model VM08 Owner’s Manual

Effect parameter details

The parameters that can be adjusted will depend on the parameter type.

Reverb effect parameters (parameter type: REVERB)

For effect types 1--24of the preceding "Effect type" table, the following four parameters can be ad- justed.

1. REVERB TIME	Adjust the length of reverberation. Range: 0.1--9.9 seconds (99 steps in 0.1 second units)
2. PRE DELAY	Adjust the time from the original sound until reverberation begins. Range: 0--100 ms
	(101 steps in 1 ms units)
3. HI RATIO	Adjust the decay ratio of the high frequencies. Range: 0--10(11 steps in increments of 1)
4. E/R BALANCE	Adjust the volume of the early reflections. Range: 0--99(100 steps in increments of 1)

Delay+reverb effect parameters (parameter type: DELAY+REVERB)

For effect types 25--28of the preceding "Effect type" table, the following four parameters can be ad- justed.

1. DELAY TIME	Adjust the delay time: Range: 1--230 ms (230 steps in 1 ms units)
	* The ENTER key / foot switch can be used for tap input (refer to p.21).
2. FEEDBACK	Adjust the number of delay repeats. Range: 0--99(100 steps in increments of 1)
3. DLY BAL	Adjust the delay balance. Range: 0--99(100 steps in increments of 1)
4. REVERB TIME	Adjust the length of reverberation. Range: 0.1--9.9 seconds (99 steps in 0.1 second units)

Delay effect parameters (parameter type: DELAY)

For effect types 29 and 30 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. DELAY TIME	Adjust the delay time. Range: 5--680 ms (136 steps in 5 ms units)
	*	The ENTER key / foot switch can be used for tap input (refer to p.21).
2. FEEDBACK	Adjust the number of delay repeats. Range: 0--99(100 steps in increments of 1)
3. HI RATIO	Adjust the decay ratio of the high frequencies. Range: 0--10(11 steps in increments of 1)
4. FILTER	Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
	*	[-]is Filter Off
	*	L1~L9 = LPF (larger numbers will lower the cutoff frequency)
	*	H1~H9 = HPF (larger numbers will raise the cutoff frequency)

BPM delay effect parameters (parameter type: BPM DELAY)

For effect types 31 and 32 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. BPM	Adjust the BPM. Range: 30--250 bpm (221 steps in units of 1)
	*	The ENTER key / foot switch can be used for tap input (refer to p.21).
2. NOTE	Select the note value for the delay. Range: 24, 16, 8T, 16...8, 4T, 8., 4, 2T, 4., 2, 2., 1
	*	24 = 16th note sextuplets, 16 = 16th notes, 8T = 8th note triplets, 16. = dotted
		sixteenth notes, 8 = 8th notes, 4T = quarter note triplets, 8. = dotted eighth notes,
		4 = quarter notes, 2T = half-note triplets, 4. = dotted quarter notes, 2 = half notes,
		2. = dotted half notes, 1 = whole notes
	*	The "." shown in the ninth character of the LCD indicates a dotted note.
	*	The "T" shown in the ninth character of the LCD indicates a triplet.
3. FEEDBACK	Adjust the number of delay repeats. Range: 0--99(100 steps in increments of 1)
4. FILTER	Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
	*	[-]is Filter Off
	*	L1~L9 = LPF (larger numbers will lower the cutoff frequency)
	*	H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Short delay effect parameters (parameter type: SHORT DELAY)

For effect type 33 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. DELAY TIME	Adjust the delay time. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10--99 ms (90 steps
	in 1 ms units), 100--200 ms (51 steps in 2 ms units)
	*	The ENTER key / foot switch cannot be used for tap input.
2. FEEDBACK	Adjust the number of delay repeats. Range: 0--99(100 steps in increments of 1)
3. HI RATIO	Adjust the decay ratio of the high frequencies. Range: 0--10(11 steps in increments of 1)
4. FILTER	Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
	*	[-]is Filter Off
	*	L1~L9 = LPF (larger numbers will lower the cutoff frequency)
	*	H1~H9 = HPF (larger numbers will raise the cutoff frequency)

22