Fostex VM08 owner manual Doubling effect parameters parameter type Doubling

Page 23

Model VM08 Owner’s Manual

Doubling effect parameters (parameter type: DOUBLING)

For effect type 34 of the preceding "Effect type" table, the following three parameters can be adjusted.

1. Lch DELAY TIME

Adjust the delay time of the L channel. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10-

 

-99 ms (90 steps in 1 ms units), 100--200 ms (51 steps in 2 ms units)

 

*

The ENTER key / foot switch cannot be used for tap input.

2. Rch DELAY TIME

Adjust the delay time of the R channel. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10-

 

-99ms(90 steps in 1 ms units), 100--200 ms (51 steps in 2 ms units)

 

*

The ENTER key / foot switch cannot be used for tap input.

3. FILTER

Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9

 

*

[-]is Filter Off

 

*

L1~L9 = LPF (larger numbers will lower the cutoff frequency)

 

*

H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Chorus effect parameters (parameter type: CHORUS)

For effect type 35 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. DEPTH

Adjust the chorus depth. Range: 0--99(100 steps in increments of 1)

2. DOUBLING TIME

Adjust the time difference of the doubling effect. Range: 0--99(100 steps in increments

 

of 1)

3. DOUBLING BALANCE

Adjust the volume of the doubling effect. Range: 0--99(100 steps in increments of 1)

4. FILTER

Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9

 

* [-]is Filter Off

 

* L1~L9 = LPF (larger numbers will lower the cutoff frequency)

 

* H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Flanger effect parameters (parameter type: FLANGE)

For effect type 36 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. RATE

Adjust the speed of modulation. Range: 0.1--2.0 Hz

(200 steps in 0.01 Hz units)

2. DEPTH

Adjust the depth of modulation. Range: 0--99(100 steps in increments of 1)

3. MOD DELAY

Adjust the modulation delay. Range: 0--200(201 steps in increments of 1)

4. FEEDBACK

Adjust the number of modulation repeats. Range:

0--99(100 steps in increments of 1)

Delay pitch effect parameters (parameter type: DELAY PITCH)

For effect type 38 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. PITCH

Adjust the amount of pitch shift. Range: -24--0--+24(49 steps in semitone units)

 

* +/-12is one octave. +/-24is two octaves.

2. ADJUST

Make fine adjustments to the amount of pitch shift. Range: -50--0--+50(101 steps in

 

increments of 1)

 

* +50 is a semitone sharp. -50is a semitone flat.

3. DLY TIME

Adjust the delay time until the pitch-shifted sound is heard. Range: 0--500(251 steps in

 

increments of 2)

 

* The ENTER key / foot switch can be used for tap input (refer to p.21).

4. FEEDBACK

Adjust the number of delay repeats. Range: 0--99(100 steps in increments of 1)

Mono pitch effect parameters (parameter type: MONO PITCH)

For effect type 37 of the preceding "Effect type" table, the following three parameters can be adjusted.

1. PITCH

Adjust the amount of pitch shift. Range: -24--0--+24(49 steps in semitone units)

 

* +/-12is one octave. +/-24is two octaves.

2. ADJUST

Make fine adjustments to the amount of pitch shift. Range: -50--0--+50(101 steps in

 

increments of 1)

 

* +50 is a semitone sharp. -50is a semitone flat.

3. MODE

Select the processing method. Range: 1--3(3 steps)

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Safety Instructions Table of Contents Names and Functions Level adjust key Contrast adjusting knobStatus indicator Fader adjust keyPlease remember this Reset of VM08Internal battery for the memory back up Remove the insulation paperInput 5/6 Input 7/8 jacks Peripheral Equipment ConnectionST.OUT L, R jack Input 1 ~ 4 jacksAUX Send OUT 1/2 jack Input 5/6 7/8 and AUX Send 1/2 jacksInput 5/6, Input 7/8 jacks Example-4 To use as a small facility mixer Application ExampleExample-2 To use as a Mono IN/STEREO OUT effects Example-3 For use as a sub-mixer for a live keyboard playerExample-8 As a practice aid for your musical instruments Example-5 For one take live studio recordingExample-6 To produce original Remix Example-7 To do you own Sound Track Video EditingVM08 Initial State Master fader display section Normal Mix ModeUseful information Character display sectionTo set to the present fader position To return to the setting before switching off powerSetting before switch off of power Mute of the various input channel/master outputNumber is adjusted with the Data encoder Channel Parameter Edit ModeSetup method for PAN setting Number is set with the Data encoder Setup method for EQ settingSetup method of the Effect Send level Example Character display section when LO is made to lightExample The character display section with light up A1 Setup method of the AUX Send levelExample Character section when E1 is lit Example The character display section with E1 is lit PRE/POST setup method for Effect SEND/AUX SendP. Fostex Advanced Signal Processing Technology Effect Edit ModeAbout the effect types Effect types preset for EFFUse the Data encoder to select the effect type When the EFF 1 key is pressedWhen the EFF 2 key is pressed Selecting the effect typeTo mute the effect sound Effect parameter settingsTo cancel muting Muting an effectEffect parameter details Flanger effect parameters parameter type Flange Delay pitch effect parameters parameter type Delay PitchDoubling effect parameters parameter type Doubling Chorus effect parameters parameter type ChorusPress the Scene Store key Scene Memory ModeStoring a scene memory Recalling a scene memoryPress the Fader Adjust key Level adjustFader adjust Press the Level Adjust keyPress the EFF 1 key or EFF 2 key Directly recalling a scene memoryClearing a scene memory Hold down the Exit key and press the Scene Recall keyDetails of the setup menu Setup ModeMaking settings in setup mode Foot Switch setting Display Foot Sw ? Fader Fix setting Display FaderFix ?Channel fader recall setting Display ChFdrRcl ? Master fader recall setting Display MsFdrRcl ?AUX Send 1/2 SpecificationsInput 1 ~ Input 5/6 ~ 7/8Declaration of EC Directive
Top Page Image Contents