Fostex VM08 owner manual Input 5/6 7/8 and AUX Send 1/2 jacks, Input 5/6, Input 7/8 jacks

Page 8

Model VM08 Owner’s Manual

5) FOOT SW jack

This is an unbalanced type phone jack. An unlatch type foot switch (Fostex Model 8051) can be plugged in here. Operations using the foot switch are selectable in the [Setup mode]. Refer to [Setup mode] on page 27 for details.

6) DC IN connector

Plug-in the tip of the power cord of the exclusive AC adaptor (AD-9B) here and plug the adaptor into a household AC wall outlet. Since the VM08 does not have a power switch, ON/OFF of power is done by plugging and unplugging the AC adaptor from the AC wall outlet. If you don’t plan on using the VM08 for some length of time, the AC adaptor must be unplugged from the AC wall outlet.

7) S/P DIF OUT connector

The same signals output from ST OUT L, R are output here as digital (S/P DIF) signals.

Signals mixed in an external digital master recorder connected here can be recorded in digital as shown in the schematic. If external digital equipment to be connected is provided with only COAXIAL (RCA pin jack) type IN/OUT connectors, use the optional Fostex COP-1/96k optical-coaxial converting adaptor sold sepa- rately.

* INPUT 5/6 (7/8) and AUX SEND 1/2 jacks

TRS type jacks used at INPUT 5/6, TRS type jacks used at INPUT 5/6 (7/8) and AUX SEND 1/2, and TRS phone plugs or unbalanced phone plugs can be connected here, as shown below. The phone plug should be wired as shown below.

TRS Phone plug

 

 

 

 

Phone plug

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT 5/6, INPUT 7/8 jacks:

* How to input a stereo signal:

In order to input a stereo output signal to chan- nels 5/6 or 7/8, a stereo cable with a STEREO phone plug wired as shown in the schematic should be used. Set the INPUT 5/6 input mode or INPUT 7/8 input mode in the setup mode to [Ste- reo]. The L signal of the stereo input signal will be applied to channel 5 (or 7) and the R signal to channel 6 (or 8). Refer to [Setup mode] on page 27 to setup the input mode.

VM08 side

Music source side

* How to input a monaural signal:

In order to input a monaural output signal to channels 5/6 or 7/8, an unbalanced phone plug, as shown in the schematic, is used for the con- nection and the INPUT 5/6 input mode or IN- PUT 7/8 input mode in the "setup mode" is set to [In 5 > Mono] (or [In 7 > Mono]).

The monaural signal will be simultaneously in- put to channels 5 and 6 (or 7 and 8). When setting the input mode, refer to [Setup mode] on page 27 for details.

VM08 side

Music source side

AUX SEND OUT 1/2 jack:

* Connecting two external equipment:

Wire the TRS phone plug to two phone plugs as shown in the schematic to connect two separate pieces of equipment to AUX SEND 1/2.

By doing so, the AUX SEND 1 signal and AUX SEND 2 signal will be separately output to the two.

VM08 side

External Equipment

* Connecting a single external equipment:

In order to connect a single external piece of equipment to the AUX SEND 1/2 jack, the unbal- anced phone plug is connected as shown in the schematic.

This will output only the AUX SEND 1 signal.

VM08 side

External Equipment

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model Safety Instructions Table of Contents Names and Functions Contrast adjusting knob Status indicatorFader adjust key Level adjust keyReset of VM08 Internal battery for the memory back upRemove the insulation paper Please remember thisPeripheral Equipment Connection ST.OUT L, R jackInput 1 ~ 4 jacks Input 5/6 Input 7/8 jacksAUX Send OUT 1/2 jack Input 5/6 7/8 and AUX Send 1/2 jacksInput 5/6, Input 7/8 jacks Application Example Example-2 To use as a Mono IN/STEREO OUT effectsExample-3 For use as a sub-mixer for a live keyboard player Example-4 To use as a small facility mixerExample-5 For one take live studio recording Example-6 To produce original RemixExample-7 To do you own Sound Track Video Editing Example-8 As a practice aid for your musical instrumentsVM08 Initial State Normal Mix Mode Useful informationCharacter display section Master fader display sectionTo return to the setting before switching off power Setting before switch off of powerMute of the various input channel/master output To set to the present fader positionNumber is adjusted with the Data encoder Channel Parameter Edit ModeSetup method for PAN setting Setup method for EQ setting Setup method of the Effect Send levelExample Character display section when LO is made to light Number is set with the Data encoderExample The character display section with light up A1 Setup method of the AUX Send levelExample Character section when E1 is lit PRE/POST setup method for Effect SEND/AUX Send Example The character display section with E1 is litEffect Edit Mode P. Fostex Advanced Signal Processing TechnologyEffect types preset for EFF About the effect typesWhen the EFF 1 key is pressed When the EFF 2 key is pressedSelecting the effect type Use the Data encoder to select the effect typeEffect parameter settings To cancel mutingMuting an effect To mute the effect soundEffect parameter details Delay pitch effect parameters parameter type Delay Pitch Doubling effect parameters parameter type DoublingChorus effect parameters parameter type Chorus Flanger effect parameters parameter type FlangeScene Memory Mode Storing a scene memoryRecalling a scene memory Press the Scene Store keyLevel adjust Fader adjustPress the Level Adjust key Press the Fader Adjust keyDirectly recalling a scene memory Clearing a scene memoryHold down the Exit key and press the Scene Recall key Press the EFF 1 key or EFF 2 keyDetails of the setup menu Setup ModeMaking settings in setup mode Fader Fix setting Display FaderFix ? Channel fader recall setting Display ChFdrRcl ?Master fader recall setting Display MsFdrRcl ? Foot Switch setting Display Foot Sw ?Specifications Input 1 ~Input 5/6 ~ 7/8 AUX Send 1/2Declaration of EC Directive
Top Page Image Contents