Fostex VM08 owner manual Peripheral Equipment Connection, ST.OUT L, R jack, Input 1 ~ 4 jacks

Page 7

Model VM08 Owner’s Manual

Peripheral Equipment Connection

The schematic below is an example of external equipment connected to the VM08.

To avoid possible speaker damage, please be sure to unplug the AC adaptor when connecting external equipment to the IN/OUT connectors of the Fostex VM08.

External Effect Unit/External Mixer etc.

Monitor Speaker

Guitar & Guitar Processer

Amplifier

Monitor headphone

Digital Master Recorder

1

						2
7				4
7
											R	ST OUT	L		PHONES
	1		7		5
9V	2	8/7	8	6/5	6	4	TRIM		TRIM		2	TRIM		1	TRIM
AD-9B
ONLY
							-10	-50	-10	-50		-10	-50		-10	-50
OUT	RESET

DC IN DIGITAL FOOT SW	AUX SEND		INPUT
6	5	3	2

Microphone

AC Adaptor

Footswitch

Synthesizer

1) ST.OUT L, R jack

These are unbalanced phone jacks where an external monitor (amplifier+ speaker) or analog master re- corder can be connected. The standard output level is -10dBV.

2) INPUT 1 ~ 4 jacks

These are unbalanced phone jacks for microphones and sound sources such as a guitar. TRIM knobs are provided for each jack by so input levels can be adjusted to match the sound source, from microphone input to line level signals.

3) INPUT 5/6 (INPUT 7/8) jacks

TRS type phone jacks for connecting line level sound sources.

As shown in the schematic, both stereo and mono output sound sources can be connected. For either type signals, the input mode can be selected using the VM08’s setup mode. Refer to [Setup mode] on page 27 for setup of the input mode. Refer to next page for details in preparing and wiring the TRS phone plug. The standard input level is -6dBV.

4) AUX SEND 1/2 jack

TRS type phone jacks where external effects and mixers can be connected. Two channels, namely, AUX SEND 1 and 2 are output here. One or two external units can be connected. See the next page for details in preparing and wiring a TRS phone plug. The standard output level is -10dBV.

7

Image 7

Contents Model Safety Instructions Table of Contents Names and Functions Level adjust key Contrast adjusting knobStatus indicator Fader adjust keyPlease remember this Reset of VM08Internal battery for the memory back up Remove the insulation paperInput 5/6 Input 7/8 jacks Peripheral Equipment ConnectionST.OUT L, R jack Input 1 ~ 4 jacksInput 5/6, Input 7/8 jacks Input 5/6 7/8 and AUX Send 1/2 jacksAUX Send OUT 1/2 jack Example-4 To use as a small facility mixer Application ExampleExample-2 To use as a Mono IN/STEREO OUT effects Example-3 For use as a sub-mixer for a live keyboard playerExample-8 As a practice aid for your musical instruments Example-5 For one take live studio recordingExample-6 To produce original Remix Example-7 To do you own Sound Track Video EditingVM08 Initial State Master fader display section Normal Mix ModeUseful information Character display sectionTo set to the present fader position To return to the setting before switching off powerSetting before switch off of power Mute of the various input channel/master outputSetup method for PAN setting Channel Parameter Edit ModeNumber is adjusted with the Data encoder Number is set with the Data encoder Setup method for EQ settingSetup method of the Effect Send level Example Character display section when LO is made to lightExample Character section when E1 is lit Setup method of the AUX Send levelExample The character display section with light up A1 Example The character display section with E1 is lit PRE/POST setup method for Effect SEND/AUX SendP. Fostex Advanced Signal Processing Technology Effect Edit ModeAbout the effect types Effect types preset for EFFUse the Data encoder to select the effect type When the EFF 1 key is pressedWhen the EFF 2 key is pressed Selecting the effect typeTo mute the effect sound Effect parameter settingsTo cancel muting Muting an effectEffect parameter details Flanger effect parameters parameter type Flange Delay pitch effect parameters parameter type Delay PitchDoubling effect parameters parameter type Doubling Chorus effect parameters parameter type ChorusPress the Scene Store key Scene Memory ModeStoring a scene memory Recalling a scene memoryPress the Fader Adjust key Level adjustFader adjust Press the Level Adjust keyPress the EFF 1 key or EFF 2 key Directly recalling a scene memoryClearing a scene memory Hold down the Exit key and press the Scene Recall keyMaking settings in setup mode Setup ModeDetails of the setup menu Foot Switch setting Display Foot Sw ? Fader Fix setting Display FaderFix ?Channel fader recall setting Display ChFdrRcl ? Master fader recall setting Display MsFdrRcl ?AUX Send 1/2 SpecificationsInput 1 ~ Input 5/6 ~ 7/8Declaration of EC Directive